manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Station Manual

Share
Download
MOTO GUZZI Stelvio 1200 NTX Service Station Manual Download Page 59

Fuses

MAIN FUSES

1 - Battery recharge (40 A).

2 - Motion main fuse (30 A).

NOTE

THERE IS ONE SPARE FUSE.

ABS MAIN FUSES

3 - ABS main fuse (40 A).

4 - ABS main fuse (25 A).

NOTE

THERE IS ONE SPARE FUSE.

AUXILIARY FUSES

A - Stop, horn, coil, GPS, hazard button lighting,

coils, light relay, passing (15 A).

B - Tail lights, starter motor (15 A).

C - Live positive, ABS power supply (10A)

D - Fuel pump, coils, injectors (15 A).

D - Lambda burner, speed sensor, auxiliary injec-

tion relay coil, start-up relay coil (15 A).

F- Permanent positive, ECU power supply (3A).

NOTE

THERE ARE TWO SPARE FUSES.

Stelvio 1200 NTX ABS

Electrical system

ELE SYS - 59

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands