manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Station Manual

Share
Download
MOTO GUZZI Stelvio 1200 NTX Service Station Manual Download Page 286

Carry out the listed checks before delivering the vehicle.

WARNING

BE EXTREMELY CAUTIOUS WHEN HANDLING FUEL.

Aesthetic inspection

- Paintwork

- Fitting of Plastic Parts

- Scratches

- Dirt

Tightening torques inspection

- Safety locks:

front and rear suspension unit

front and rear brake calliper retainer unit

front and rear wheel unit

engine - chassis retainers

steering assembly

- Plastic parts fixing screws

Electrical system

- Main switch

- Headlamps: high-beam lights, low-beam lights, tail lights (front and rear) and their warning lights

- Headlight adjustment according to regulations in force

- Front and rear stop light switches and their bulbs

- Turn indicators and their warning lights

- Instrument panel lights

- Instrument panel: fuel and temperature indicator (if present)

- Instrument panel warning lights

- Horn

- Electric start-up

- Engine stop via emergency stop switch and side stand

- Helmet compartment electrical opening switch (if present)

Pre-delivery

Stelvio 1200 NTX ABS

PRE DE - 286

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands