manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Station Manual

Share
Download
MOTO GUZZI Stelvio 1200 NTX Service Station Manual Download Page 122

Installing the generator

•

If the sealing ring has been previously

removed, replace it using the punch of

the timing system cover sealing ring.

Specific tooling

05.92.72.30

 

Timing system cover sealing ring

punch

•

Place the bolt and the pin in the gen-

erator cover.

•

Replace the gasket and place the al-

ternator frame using the front cover in-

sertion cone.

•

Remove the insertion cone afterwards.

Specific tooling

05.91.17.30

 

Front cover insertion cone

•

Tighten the two screws.

Engine

Stelvio 1200 NTX ABS

ENG - 122

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands