MOTO GUZZI Stelvio 1200 NTX Service Station Manual Download Page 11

Page: 11 / 290

This number consists of numbers and letters, as in

the example shown below.

ZGULZB010YMXXXXXX

KEY:

ZGU

: WMI (World manufacturer identifier) code;

: model;

B01

: version variation;

: free digit

year of manufacture

: production plant (M= Mandello del Lario);

XXXXXX

: serial number (6 digits);

CHASSIS NUMBER

The chassis number is stamped on the right hand

side of the headstock.

ENGINE NUMBER

The engine number is stamped on the left side,

close to the engine oil level check cap.

Dimensions and mass

WEIGHT AND DIMENSIONS

Specification

Desc./Quantity

Maximum width (without accessories)

2305 mm (90.75 in)

Maximum width at handlebar

910 mm (35.83 in)

Maximum width of vehicle with accessories

1080 mm (42.52 in)

Minimum / maximum height (adjustable windshield)

1395 / 1440 mm (54.92 / 56.69 in)

Saddle height

800 mm (31.5 in)

Minimum ground clearance

185 mm (7.3 in)

Wheelbase

1535 mm (60.43 in)

Kerb weight

251 kg (553 lb)

Kerb weight of vehicle with accessories

278 kg (613 lb)

Engine

ENGINE

Specification

Desc./Quantity

Type

Four stroke 90° transverse V-twin

Number of cylinders

Cylinder layout

90° V

Stelvio 1200 NTX ABS

Characteristics

CHAR - 11

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



































































































































































































































































































Search results

Summary of Contents for Stelvio 1200 NTX

Reviews:

Brands by name

Popular brands

MOTO GUZZI Stelvio 1200 NTX, Service Station Manual

Search results

Summary of Contents for Stelvio 1200 NTX

Reviews:

Brands by name

Popular brands