manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Station Manual

The MOTO GUZZI Stelvio 1200 NTX is a powerful and reliable adventure bike designed to tackle any terrain. To maintain its optimal performance, it's essential to have the Service Station Manual at hand for routine maintenance. Download this comprehensive manual for free from manualshive.com, ensuring you have all the information you need at your fingertips.

Share
Download
background image

Seat

•

Rest the vehicle on its stand.

•

Insert the key in the saddle lock.

•

Turn the key clockwise and slightly

press the centre of the passenger seat

rear part to facilitate releasing the pin.

•

Lift the passenger seat and slide it off

from behind.

•

Unscrew and remove the knobs fixing

the rider saddle.

•

Remove the rider saddle.

CAUTION

BEFORE LOWERING AND LOCKING THE SADDLE,
CHECK THAT THE KEY HAS NOT BEEN LEFT INSIDE THE
GLOVE-BOX / TOOLKIT COMPARTMENT

.

Engine guard

ENSURE THAT THE ENGINE AND THE THERMAL PARTS OF THE VEHICLE ARE COLD BEFORE
OPERATING ACCORDING TO THE FOLLOWING INSTRUCTIONS. PARK THE VEHICLE ON
STAND ON FIRM AND LEVEL GROUND.

•

Undo the screw and remove the rear

brake oil reservoir.

•

From the left side of the vehicle, re-

move the nut (1) and the correspond-

ing washer.

•

Slide off the frame pin (2) from the right

side with the corresponding washer.

Stelvio 1200 NTX ABS

Bodywork

BODYW - 267

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



































































































































































































































































































Reviews:

No comments

Related manuals for Stelvio 1200 NTX

R&G BRG0013 Fitting Instructions Manual preview
BRG0013
Brand: R&G Pages: 9
Yamaha YZFR6X(C) Owner'S Manual preview
YZFR6X(C)
Brand: Yamaha Pages: 120
Dayi Motor E-ODIN 2.0 Instructions Manual preview
E-ODIN 2.0
Brand: Dayi Motor Pages: 18
SW-Motech SBL.07.565.100 Mounting Instructions preview
SBL.07.565.100
Brand: SW-Motech Pages: 2
SW-Motech HPS.11.258.900-01 Mounting Instructions preview
HPS.11.258.900-01
Brand: SW-Motech Pages: 2
SW-Motech TRT.00.787.32500/B Mounting Instructions preview
TRT.00.787.32500/B
Brand: SW-Motech Pages: 6
Montesa 4ride Owner'S Manual preview
4ride
Brand: Montesa Pages: 114
Montesa 4Ride MST260 2016 Shop Manual preview
4Ride MST260 2016
Brand: Montesa Pages: 158
Vetter Terraplane Driver'S/Owner'S Manual preview
Terraplane
Brand: Vetter Pages: 11
Aosom 370-110V80 Assembly Instruction Manual preview
370-110V80
Brand: Aosom Pages: 25
Cagiva V RAPTOR 1000 Specifications - Operation - Maintenance preview
V RAPTOR 1000
Brand: Cagiva Pages: 142
ZTechnik Z2373 Installation And Owner'S Manual preview
Z2373
Brand: ZTechnik Pages: 3
ZTechnik Z2442 Installation And Owner'S Manual preview
Z2442
Brand: ZTechnik Pages: 5
Beta RR 400 Operating Instructions Manual preview
RR 400
Brand: Beta Pages: 392
Beta ALP 200 Manual preview
ALP 200
Brand: Beta Pages: 408
Abus 40371 Instruction Manual preview
40371
Brand: Abus Pages: 18
hepco & becker 701998 00 01 Manual preview
701998 00 01
Brand: hepco & becker Pages: 2
Gazzini 10039621 Instructions For Use Manual preview
10039621
Brand: Gazzini Pages: 31

Brands by name

Popular brands

Load more brands