manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Station Manual

Share
Download
MOTO GUZZI Stelvio 1200 NTX Service Station Manual Download Page 251

Devices activation screen page

DEVICES ACTIVATION

This screen page is used to delete errors in the

control unit memory and to activate some systems

controlled by the control unit.

DEVICES ACTIVATION

Specification

Desc./Quantity

Deleting stored errors

By pressing the 'ENTER' button, the stored errors (MEM) be-

come part of the historical data (STO). In the next connection

between the Axone and the control unit, the historical errors

(STO) are no longer shown

Errors display screen page

ERRORS DISPLAY

This screen page shows potential errors detected

in the vehicle (ATT) or stored in the control unit

(MEM) and it allows to check error clearing (STO).

ERRORS DISPLAY

Specification

Desc./Quantity

Front speed sensor open circuit or short circuit

- see (DIAGNOSIS)

Rear speed sensor open circuit or short circuit

- see (DIAGNOSIS)

Front speed sensor coherence

- see (DIAGNOSIS)

Rear speed sensor coherence

- see (DIAGNOSIS)

ABS motor pump

- see (DIAGNOSIS)

ABS valve relay

- see (DIAGNOSIS)

Front inlet valve

- see (DIAGNOSIS)

Rear inlet valve

- see (DIAGNOSIS)

Front outlet valve

- see (DIAGNOSIS)

Rear outlet valve

- see (DIAGNOSIS)

Control unit

- see (DIAGNOSIS)

Diagnosis

In diagnosis mode (Axone communicating with the ABS module) the system is not active and does not

recognise some errors (for instance, speed difference between the wheels).

Stelvio 1200 NTX ABS

Braking system

BRAK SYS - 251

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands