manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Station Manual

The MOTO GUZZI Stelvio 1200 NTX is a powerful and reliable adventure bike designed to tackle any terrain. To maintain its optimal performance, it's essential to have the Service Station Manual at hand for routine maintenance. Download this comprehensive manual for free from manualshive.com, ensuring you have all the information you need at your fingertips.

Share
Download
background image

•

Undo and remove the two radiator up-

per screws and collect the washer.

•

Remove the oil cooling radiator.

Installing

•

Fit the oil cooling radiator on the vehi-

cle following the operations described

in the removal chapter but in reverse

order.

•

Pull out the oil filler plug / oil level dip-

stick (1).

•

Pour new oil until it goes over the min-

imum level marked "MIN" on the dip-

stick (1).

•

Insert the oil filler plug / oil level dipstick

(1).

•

Start the vehicle and let the engine run

for a few minutes so that the oil circu-

lates and fills the radiator internal

ducts.

•

Stop the engine and check the oil level

with the dipstick (1).

•

Fill with engine oil as required.

Chassis

Stelvio 1200 NTX ABS

CHAS - 242

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



































































































































































































































































































Reviews:

No comments

Related manuals for Stelvio 1200 NTX

Öhlins YA919 Mounting Instructions preview
YA919
Brand: Öhlins Pages: 2
Yamaha Star XV250ZC Owner'S Manual preview
Star XV250ZC
Brand: Yamaha Pages: 96
R&G FI0054BK Fitting Instructions preview
FI0054BK
Brand: R&G Pages: 4
R&G BRG0013 Fitting Instructions Manual preview
BRG0013
Brand: R&G Pages: 9
Nolan N60-5 Safety And Instructions For Use preview
N60-5
Brand: Nolan Pages: 80
Victory Motorcycles 2016 Empulse TT Rider'S Manual preview
2016 Empulse TT
Brand: Victory Motorcycles Pages: 138
ESAB WARRIOR TECH User Instructions preview
WARRIOR TECH
Brand: ESAB Pages: 4
Yoshimura RACE 11621C0520 Manual preview
RACE 11621C0520
Brand: Yoshimura Pages: 7
Hudora Cruiser 12“ Instructions On Assembly And Use preview
Cruiser 12“
Brand: Hudora Pages: 8
Wunderlich 35520-002 Manual preview
35520-002
Brand: Wunderlich Pages: 2
Memphis Shades MEM-9890 Mounting Instructions preview
MEM-9890
Brand: Memphis Shades Pages: 2
Memphis Shades 2321-0045 Mounting Instructions preview
2321-0045
Brand: Memphis Shades Pages: 2
Memphis Shades 2320-0037 Mounting Instructions preview
2320-0037
Brand: Memphis Shades Pages: 2
MARLINK SmallTrack Assembly Instructions preview
SmallTrack
Brand: MARLINK Pages: 3
X-lite X-403GT Safety And Instructions For Use preview
X-403GT
Brand: X-lite Pages: 116
Yamaha 2003 AG200F Supplementary Service Manual preview
2003 AG200F
Brand: Yamaha Pages: 20
Yamaha 2003 FJR1300 Service Manual preview
2003 FJR1300
Brand: Yamaha Pages: 162
Yamaha 2003 TZR50 Service Manual preview
2003 TZR50
Brand: Yamaha Pages: 251

Brands by name

Popular brands

Load more brands