manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Station Manual

Share
Download
MOTO GUZZI Stelvio 1200 NTX Service Station Manual Download Page 93

•

Operating from both sides, tighten the

upper engine fixing nut on the internal

side of the chassis.

•

Fit the centre stand.

•

Operating from both sides, tighten the

screws fixing the centre stand plates.

•

Remove the engine service stand from

under the oil sump.

•

Working from both sides, place the in-

let manifold fitting a new gasket be-

tween the manifold and head.

•

Fasten the inlet manifold with the three

screws.

•

Connect the stand sensor connector

and fix it to the chassis with new

clamps.

Stelvio 1200 NTX ABS

Engine from vehicle

ENG VE - 93

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands