manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Station Manual

Share
Download
MOTO GUZZI Stelvio 1200 NTX Service Station Manual Download Page 147

•

Lock crankshaft rotation.

•

Unscrew and remove the nut fixing the

crankshaft gear.

•

Remove the oil pump control gear.

Specific tooling

12.91.18.01

 

Tool to lock the flywheel and the

starting ring gear

•

Fit the timing system gear and align the

reference with that on the crankshaft

gear. Turn the crankshaft to align the

two gears.

•

After shimming the timing sensor prop-

erly, proceed to fit it.

•

Fit the washer and tighten the timing

system gear fixing nut of the service

shaft.

Stelvio 1200 NTX ABS

Engine

ENG - 147

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands