manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Station Manual

Share
Download
MOTO GUZZI Stelvio 1200 NTX Service Station Manual Download Page 158

•

Fix the head with the two screws.

•

Tighten nuts and screws to the prescri-

bed torque operating diagonally and in

stages.

•

Loosen the valve set screws.

•

Using a thin screwdriver relief oil pres-

sure from the left cylinder chain ten-

sioner.

•

Screw two screws in the threaded

holes of the timing system upper gear.

•

Rotate the camshaft so that its pin is

aimed towards the hole in the timing

system chain.

•

Place the gear in the chain.

•

On the left camshaft pin, fit the hole

marked with the letter "L" of the timing

system gear.

•

Block the left chain tensioner hole with

screw and washer.

•

Rotate the crankshaft by 90°so that the

right cylinder piston reaches the TDC;

lock crankshaft rotation.

•

Also determine the thickness of the

gasket for the right cylinder, to be fitted

between the head and the cylinder as

described in the section: Shimming

system.

•

Place the two dowel pins.

Engine

Stelvio 1200 NTX ABS

ENG - 158

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands