manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Station Manual

Share
Download
MOTO GUZZI Stelvio 1200 NTX Service Station Manual Download Page 35

•

Place a container with +4,000 cm³ (244

cu in) capacity under the drainage plug

(3).

•

Unscrew and remove the drainage

plug (3).

•

Pull out the oil filler plug / engine oil

level dipstick (4).

•

Drain the oil into the container; allow

several minutes for oil to drain out com-

pletely.

•

Insert the oil filler plug / engine oil level

dipstick (4).

•

Check and if necessary, replace the

drainage plug (3) sealing washers.

•

Remove any metal deposits attached

to the drainage plug (3) magnet.

•

Screw and tighten the drainage plug

(3).

DO NOT DISPOSE OF OIL INTO THE ENVIRONMENT.
DISPOSE OF ENGINE OIL STORED IN A SEALED CON-
TAINER AND TAKE IT TO YOUR SUPPLIER OR TO THE
NEAREST USED OIL RECLAMATION FIRM.

Engine oil filter

Replace the engine oil filter each time you

change the engine oil.

•

Drain the engine oil completely.

•

Unscrew and remove the engine oil fil-

ter from its seat.

NOTE

NEVER REUSE AN OLD FILTER.

•

Spread a thin layer of oil on the sealing ring of the new engine oil filter.

•

Fit and screw the new oil filter in its seat.

See also

Replacement

Stelvio 1200 NTX ABS

Maintenance

MAIN - 35

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands