manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Station Manual

Share
Download
MOTO GUZZI Stelvio 1200 NTX Service Station Manual Download Page 143

•

Place the camshaft with the gear seat

on the dowel side.

•

Place the U-bolt on the camshaft mak-

ing sure the two reference pins match

the seats on the cam tower.

•

Tighten the four screws operating di-

agonally and in stages.

Timing

Removing the phonic wheel

•

Remove the generator and the timing

system cover.

•

Unscrew and remove the nut and col-

lect the washer.

•

Remove the timing system gear on the

service shaft.

•

Remove the timing sensor and any

shim washers.

•

Remove the tone wheel.

•

Remove the cotter and shim washer

from the service shaft.

See also

Stelvio 1200 NTX ABS

Engine

ENG - 143

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands