MOTO GUZZI California 1400 Instructions Manual Download Page 56 | Manualshive

Page: 56 / 411

MOTO GUZZI California 1400 Instructions Manual Download Page 56

•

Unscrew and remove the breather cap (3).

•

Drain the oil into the container; allow several minutes for oil to drain out completely.

•

Check and if necessary, replace the sealing washer of drainage plug (5).

•

Remove any metal scrap attached to the drainage plug (5) magnet.

•

Screw and tighten the drainage plug (5).

•

Pour new oil through the fill opening (4) until it reaches the cap/dipstick hole (4).

CAUTION

DO NOT ADD ADDITIVES OR ANY OTHER SUBSTANCE TO THE FLUID. WHEN USING A FUNNEL
OR ANY OTHER ELEMENT, MAKE SURE IT IS PERFECTLY CLEAN.

•

Screw and tighten the caps (3 - 4).

Engine oil

Check

CAUTION

ENGINE MUST BE WARM TO CHECK ENGINE OIL LEVEL.

NOTE

DO NOT LET THE ENGINE IDLE WITH THE VEHICLE AT STANDSTILL TO WARM UP THE ENGINE
OIL AND REACH THE OPERATING TEMPERATURE OF ENGINE OIL. OIL IS BEST CHECKED
AFTER RUNNING FOR ABOUT 15 KM (10 miles).

•

Shut off the engine.

•

Keep the vehicle upright with both wheels on the ground.

Maintenance

California 1400

MAIN - 56

«
...
54
55
56
57
58
...
»

Summary of Contents for California 1400




























































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands