MOTO GUZZI California 1400 Instructions Manual Download Page 116

Page: 116 / 411

with the vehicle ground connection: if it is grounded, restore the cable harness. If OK, replace the control

unit. If PIN 2 has approx. 12 V, check continuity of the yellow cable between PIN 1 of the sensor on the

cable harness side and PIN 12 of the ABS control unit connector. If this is not OK, restore the cable

harness. If it is OK, replace the sensor.

P0502 Rear wheel speed signal/sensor.

Connect to the ABS control unit diagnostics.

LOGIC ERRORS

Speed sensor

5DA1 the signal works irregularly:

faulty sensor or signal interference.

Troubleshooting:

Check speed sensor retainer. If it is not OK, restore it. If it is OK, check if the tone

wheel is dirty, deformed or wrongly fixed. If any of this happens, replace the tone wheel. Otherwise,

replace the speed sensor.

5DA2 the signal decreases periodically:

Possible tone wheel fault due to deformations or dirt; pos-

sible alterations on the wheel bearing surface. In very rare cases, abnormal tone wheel vibrations.

Troubleshooting:

Check if the tone wheel is dirty, deformed or wrongly fixed. If the tone wheel is not

OK, replace it. If it is OK, check for possible faults in the wheel bearings and if it is not OK, replace the

bearings.

5DA3 no signal or speed measured too low in relation to the front wheel:

Faulty sensor or missing

sensor/tone wheel. Or excessive distance between the sensor and the tone wheel or tone wheel with

wrong number of teeth.

Troubleshooting:

Check that the speed sensor and the tone wheel are installed. If they are not, install

them. If they are, check the speed sensor retainer. If it is not OK, restore it. If it is, check if the tone

wheel has the correct number of teeth or if it is dirty, deformed or wrongly fixed. If it is not OK, replace

the tone wheel and if it is OK, replace the speed sensor.

5DA4 missing acceleration after pressure reduction:

Faulty sensor or missing sensor/tone wheel

or excessive distance between the sensor and the tone wheel.

Troubleshooting:

Check that the speed sensor and the tone wheel are installed. If they are not, install

them. If they are, check the speed sensor retainer. If it is not OK, restore it. If it is, check if the tone

wheel has the correct number of teeth or if it is dirty, deformed or wrongly fixed. If it is not OK, replace

the tone wheel and if it is OK, replace the speed sensor.

5DA5 excessive measured speed:

Faulty sensor or tone wheel, or tone wheel with wrong number of

teeth or wrong tyre size.

Troubleshooting:

Check that the speed sensor and the tone wheel are installed. If they are not, install

them. If they are, check the speed sensor retainer. If it is not OK, restore it. If it is, check if the tone

wheel has the correct number of teeth or if it is dirty, deformed or wrongly fixed. If it is not OK, replace

the tone wheel and if it is OK, check that the tyre size is the correct one. If it is not OK, replace it. If it is

Electrical system

California 1400

ELE SYS - 116

Summary of Contents for California 1400




























































































































































































































































































































































































































Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands

MOTO GUZZI California 1400, Instructions Manual

Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands