MOTO GUZZI California 1400 Instructions Manual Download Page 248

Page: 248 / 411

•

The reference on the piston ring must

be facing the piston crown.

•

Fit the piston rings on the piston: - the

oil scraper in the lower slot; - the thicker

smooth ring in the intermediate slot; -

the less thick smooth ring in the upper

slot.

•

The piston rings must be offset at 120°

one from the other.

•

Fit one of the two pin snap rings on the

piston.

•

Lock crankshaft rotation.

Specific tooling

12.91.18.01

Tool to lock the flywheel and the

starting ring gear

•

Fit the piston.

NOTE

CHECK THE ORIENTATION OF THE PISTON ACCORDING TO THE REFERENCES AT THE TOP.
DO NOT ASSEMBLE PISTONS AND CYLINDERS OF DIFFERENT SELECTOR TYPES.

•

Insert the pin.

•

Insert the snap ring.

Specific tooling

020470Y

Pin snap ring fitting tool

Engine

California 1400

ENG - 248

Summary of Contents for California 1400




























































































































































































































































































































































































































Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands

MOTO GUZZI California 1400, Instructions Manual

Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands