MOTO GUZZI California 1400 Instructions Manual Download Page 239

Page: 239 / 411

Removing the phonic wheel

Installing the service shaft

•

Place the service shaft bearing (if pre-

viously removed) on the crankcase.

•

Fix it to the seat with the lock washer

and screw.

•

Fit the timing chains according to the

references marked at the removal

phase.

•

Lubricate the service shaft.

•

Insert the service shaft in its crankcase

seat by sliding it through the two

chains.

•

Fit each chain to the corresponding

service shaft gear.

•

Fit the roller cage and a new O-ring on

the service shaft closing cap.

•

Partially fit the service shaft closing

cap.

•

To screw the cap until it stops, use two

M6 flanged screws larger than the orig-

inal screws.

•

Tighten the two M6 flanged screws op-

erating in stages until the cap stops

against the crankcase.

California 1400

Engine

ENG - 239

Summary of Contents for California 1400




























































































































































































































































































































































































































Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands

MOTO GUZZI California 1400, Instructions Manual

Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands