MOTO GUZZI California 1400 Instructions Manual Download Page 250

Page: 250 / 411

•

Fit the movable chain slider.

•

Fit the upper gear.

•

Fit the chain tensioner and the chain

tensioner cap temporarily and keep the

chain taut on the service shaft.

LEFT CYLINDER

•

Fit the piston.

•

Remove the cloth used to prevent for-

eign bodies from getting into the crank-

case.

•

Turn the rings so that the coupling ends

are 120 degrees from each other.

•

Place a new metal gasket between the

crankcase and the cylinder.

•

Place the two dowel pins on the stud

bolts.

•

Undo the screw which will be used to

time the upper gear.

•

Check that the oil in the left cylinder

chain tensioner has been drained off

by compressing it. If the operation is

difficult, use a pin drive to push the

central hole so that the oil is drained off

from the circuit.

•

Fit the chain tensioner in the cylinder.

•

Lubricate the piston and the cylinder.

•

Lock connecting rod motion with the

fork tool.

•

Using the suitable piston ring clamp

tool, place the cylinder and fit the chain

in the timing system plate.

CAUTION

Engine

California 1400

ENG - 250

Summary of Contents for California 1400




























































































































































































































































































































































































































Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands

MOTO GUZZI California 1400, Instructions Manual

Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands