MOTO GUZZI California 1400 Instructions Manual Download Page 134

Page: 134 / 411

(between the sensor connector PIN 3 and the ENGINE PIN 38) and restore the cable har-

ness.

WARNING

The control unit does not detects the following malfunctions of the oxygen sensor circuit according to

the signal: interrupted circuit, shorted to ground or sensor malfunction (for example non variable volt-

age). In case of fault indication, carry out the following troubleshooting.

Troubleshooting

•

Check circuit continuity from probe connector (PIN 1 and PIN 2) toward the probe: replace

the oxygen sensor if there is no continuity; if there is continuity, check the sensor connector

and the Marelli control unit connector: If not OK, restore. If OK, check continuity between

the ENGINE connector PIN 38 and PIN 9 and restore the cable harness.

Injector

Injectors key:

1. Left injector

2. Right injector

INJECTOR

Function

To supply the correct amount of petrol at the right timing.

Operation / Operating principle

Injector coil is energised for the petrol passage to open

Level in electrical circuit diagram:

Coils and injectors

Location:

Electrical system

California 1400

ELE SYS - 134

Summary of Contents for California 1400




























































































































































































































































































































































































































Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands

MOTO GUZZI California 1400, Instructions Manual

Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands