MOTO GUZZI California 1400 Instructions Manual Download Page 241

Page: 241 / 411

Cam timing

•

Fit the crankshaft and the service shaft

on the crankcase.

•

Fit the cylinders.

•

Turn the crankshaft until the left cylin-

der piston reaches the top dead centre

(TDC).

•

Fit the cotter and the shim washer on

the service shaft.

•

Fit the tone wheel with the chamfered

side facing the crankcase on the serv-

ice shaft.

•

Lock crankshaft rotation.

•

Unscrew and remove the nut fixing the

crankshaft gear.

•

Remove the oil pump control gear.

Specific tooling

12.91.18.01

Tool to lock the flywheel and the

starting ring gear

•

Fit the timing system gear and align the

reference with that on the crankshaft

gear. Turn the crankshaft to align the

two gears.

California 1400

Engine

ENG - 241

Summary of Contents for California 1400




























































































































































































































































































































































































































Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands

MOTO GUZZI California 1400, Instructions Manual

Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands