MOTO GUZZI California 1400 Instructions Manual Download Page 293

Page: 293 / 411

•

Hold the motorcycle front section.

•

Loosen the screw on the wheel axle

clamp.

•

Undo and remove the wheel axle.

•

During the pin extraction operation,

support the wheel and then remove it.

Checking the front wheel

FRONT WHEEL BEARINGS

Carry out the check with the bearings fitted on the wheel.

CHECK THAT ALL PARTS ARE IN GOOD CONDITION, ESPECIALLY THOSE LISTED AS FOL-
LOWS.

ROTATION CHECK

•

Manually rotate the inside ring of each bearing. Rotation must be constant, smooth and

noiseless.

If one or both bearings do not fall within the control parameters:

California 1400

Suspensions

SUSP - 293

Summary of Contents for California 1400




























































































































































































































































































































































































































Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands

MOTO GUZZI California 1400, Instructions Manual

Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands