manualshive.com logo in svg

MOTO GUZZI California 1400, Instructions Manual

Share
Download
MOTO GUZZI California 1400 Instructions Manual Download Page 232

OUTLET VALVE SEAT DETAIL DRAWING

- If the width of the mark on the valve seat is larger than the prescribed limits, true the seats with a 45°

milling cutter and then grind.

- Replace the head in case of excessive wear or damage.

Installing the valves

NOTE

THE FOLLOWING OPERATIONS REFER TO REMOVING ONLY ONE HEAD BUT APPLY TO BOTH
HEADS.

•

Place the valve guide oil seal (4) in the

head.

•

Place the lower cap (5).

•

Place the valve (6) inside the head.

•

Place the spring (3).

•

Fit the upper cap (2).

•

Place the two cotters (1) on the seats

in the valves.

•

By compressing the spring (3) with the

special tool, fit the valve cotters.

Specific tooling

10.90.72.00

 

Tool for valve removal and refitting

AP9100838

 

Tool for valve pressure plate

•

Remove the special tool

Engine

California 1400

ENG - 232

Summary of Contents for California 1400




























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands