MOTO GUZZI California 1400 Instructions Manual Download Page 306

Page: 306 / 411

•

O-Ring on the cap.

Reassembling the fork

•

Lock the sleeve in the vice.

•

Lubricate the stanchion sliding edges with fork oil or grease for seals.

•

Install the lower and upper bushing on the stanchion, the dust scraper, the seal ring and the

washer.

•

Position the stanchion in the sleeve

and with the prescribed tool put the oil

seal in position.

Specific tooling

AP8145758

Tool for oil seals fitting

Suspensions

California 1400

SUSP - 306

Summary of Contents for California 1400




























































































































































































































































































































































































































Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands

MOTO GUZZI California 1400, Instructions Manual

Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands