MOTO GUZZI California 1400 Instructions Manual Download Page 364

Page: 364 / 411

•

Remove the rubber protection cover

from the bleed valve.

•

Insert the transparent plastic pipe in

the rear brake calliper bleed valve and

insert the other end of this pipe into a

container to collect the fluid.

•

Remove the rear brake oil reservoir

cap.

•

Operate the brake lever and then open

the bleed valve on the calliper 1/4 of a

turn to let the air out.

•

Close the bleed again before reaching

the lever end of the stroke and repeat

the operation until there is no air.

•

Screw the bleeding valve and remove the pipe.

•

Top-up the reservoir until the correct brake fluid level is obtained.

•

Refit and lock the rear brake oil reservoir cap.

•

Refit the rubber protection cover.

Braking system

California 1400

BRAK SYS - 364

Summary of Contents for California 1400




























































































































































































































































































































































































































Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands

MOTO GUZZI California 1400, Instructions Manual

Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands