MOTO GUZZI California 1400 Instructions Manual Download Page 404

Page: 404 / 411

Specific operations for the vehicle

ANTI-THEFT DEVICE

•

Remove the left fairing.

•

Cut the indicated clamp and free the

LED connector.

•

Take half of the adhesive backed foam

in the anti-theft device kit and stick it to

the bottom of the anti-theft control unit.

•

Position the clamps in the specific

seats prepared on the mounting plas-

tic.

•

Pass the right clamp through the two

slots on the anti-theft device control

unit.

•

Pull the clamps, securing the control

unit to the bracket.

•

Connect the control unit and LED con-

nectors to the specific cable harness

on the bike and attach the adhesive

LED on the internal side of the left side

fairing.

Pre-delivery

California 1400

PRE DE - 404

Summary of Contents for California 1400




























































































































































































































































































































































































































Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands

MOTO GUZZI California 1400, Instructions Manual

Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands