MOTO GUZZI California 1400 Instructions Manual Download Page 406

Page: 406 / 411

•

Collect the fixing screws (5) from the

heatable handgrip (4).

•

Position the heatable handgrip all the

way, taking care to align the holes on

the grip with those on the handlebar,

and screw in the fixing screws (5).

•

Replace the two cable grommets with

the ones in the kit (6). Also, take care

to insert the cabling of the heatable

handgrip in the rubber cable grommet

(7).

•

Pass the cable behind the steering col-

umn and connect it to one of the two

available connectors.

Pre-delivery

California 1400

PRE DE - 406

Summary of Contents for California 1400




























































































































































































































































































































































































































Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands

MOTO GUZZI California 1400, Instructions Manual

Search results

Summary of Contents for California 1400

Reviews:

Brands by name

Popular brands