Mitsubishi Electric MELSEC iQ-F FX55-ASL-M User Manual Download Page 47 | Manualshive

Page: 47 / 96

background image

6 WIRING

6.1 Terminal Block

45

6

6

WIRING

This chapter describes the wiring of the FX5-ASL-M.

6.1

Terminal Block

Type of the terminal block

The following terminal block is used in the FX5-ASL-M.

Tightening torque

Tighten terminal block screws within the following tightening torque range.

To connect the terminal block, a flathead screwdriver having a tipped size of 0.4



2.5 mm is required.

Before removing the transmission cable terminal block, check that the terminal block mounting screws on both sides are
completely loosened (removed from the socket).
Pulling with excessive force while the terminal block mounting screws on the both sides are still tightened may damage the
device.
Before tightening, check that there are no short circuits due to disconnected or frayed wires. Then tighten the terminal block
mounting screws on both sides securely.

Signal name of the terminal block

The following shows the signal names of the terminal block.

Name

Model

Contact

Transmission cable terminal block

FMC1,5/7-STF-3,81

PHOENIX CONTACT GmbH & Co. KG

Screws tightened

Tightening torque range

Terminal block mounting screw

0.2 to 0.3 N



m

Terminal block

Signal name

Description

IN

24V

Power supply terminals for driving the transmission circuit of the AnyWireASLINK system and for a slave
module.
Connect to a 24 V DC external power supply.

0V

OUT

24V

Terminals for connecting isolation (4-wire) slave modules.
If the modules are connected to these terminals, supplying power for each module from the 24 V DC external
power supply is not necessary.

0V

DP

AnyWireASLINK transmission signal terminals
DP: Transmission cable (+), DN: Transmission cable (-)
Connect to the DP and DN terminals on the slave module or terminating unit.

DN

LG

Connected to the neutral point of the noise filter inserted between the 24V and 0V terminals.
Ground the LG terminal with the functional ground terminal (FG terminal) on the programmable controller at a
single point.

DP

DN

LG

24V

IN

OUT

0V

24V

0V

«
...
45
46
47
48
49
...
»

Summary of Contents for MELSEC iQ-F FX55-ASL-M

































































































Reviews:

No comments

Related manuals for MELSEC iQ-F FX55-ASL-M

Brand: Nelson Pages: 19

Brand: C-TEC Pages: 2

vlt soft starter mcd 500

Brand: Danfoss Pages: 95

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 33

Brand: Danfoss Pages: 59

Brand: Danfoss Pages: 16

VLT AQUA Drive FC 200

Brand: Danfoss Pages: 91

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 100

Brand: Danfoss Pages: 82

Brand: Danfoss Pages: 18

Brand: Danfoss Pages: 12

OPTYMA Plus OP-LPQM

Brand: Danfoss Pages: 8

Brand: Harmonic Drive Pages: 25

Brand: Nelson Pages: 8

Brand: ECKELMANN Pages: 178

Brand: echoflex Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands