manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-F FX55-ASL-M, User Manual

Share
Download
Mitsubishi Electric MELSEC iQ-F FX55-ASL-M User Manual Download Page 3

1

COPYRIGHT

This document is protected by the law of copyright, whereby all rights established therein remain with the company Mitsubishi 
Electric Corporation. Reproduction of this document or parts of this document is only permissible within the limits of the legal 
determination of Copyright Law. Alteration or abridgement of the document is not permitted without the explicit written 
approval of the company Mitsubishi Electric Corporation.

PRECAUTIONS REGARDING WARRANTY AND 

SPECIFICATIONS

The FX5-ASL-M is jointly developed and manufactured by Mitsubishi Electric and Anywire Corporation. Note that there are 
differences in warranty.
  • Warranty

 • Application of the EMC Directive

 • Application of the UL/cUL standards

Item

FX5-ASL-M

Other programmable controller products (e.g. 
MELSEC iQ-F series)

Repair term after discontinuation of production

1 year

7 years

Item

FX5-ASL-M

Other programmable controller products (e.g. 
MELSEC iQ-F series)

Applicable EMC standard

EN61131-2

EN61131-2

Item

FX5-ASL-ML

Other programmable controller products (e.g. 
MELSEC iQ-F series)

Applicable UL standard/cUL standard

UL508

UL508

Summary of Contents for MELSEC iQ-F FX55-ASL-M

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands