Mitsubishi Electric MELSEC iQ-F FX55-ASL-M User Manual Download Page 25 | Manualshive

Page: 25 / 96

background image

4 FUNCTION

4.2 AnyWireASLINK Transmission

23

4

4.2

AnyWireASLINK Transmission

The AnyWireASLINK is a high-speed and highly reliable system which releases the work site from complicated and incorrect
wiring.
In AnyWireASLINK, the FX5-ASL-M communicates with slave modules using IDs (addresses) of the slave modules.
The IDs (addresses) of the slave modules are stored in the buffer memory of the FX5-ASL-M.

Bit transmission

A maximum of 384 I/O data points (input max. 256 points, output max. 256 points) can be exchanged between the FX5-ASL-
M and a slave module.

(1) CPU module
(2) FX5-ASL-M
(3) Input slave module (ASLINKER): Address 0
(4) Output slave module (ASLINKER): Address 0
(5) Buffer memory
(6) Sensor switch
(7) LED

(1)

(2)

(5)

M2000
M2001
M2002

M2255

M3000
M3001
M3002

M3255

(3)

ID: 200H

IN 1

IN 0

(4)

(6)

(7)

ID: 0H

OUT 1

OUT 0

U1\G0.0
U1\G0.1
U1\G0.2

U1\G15.F

U1\G4096.0
U1\G4096.1
U1\G4096.2

U1\G4111.F

«
...
23
24
25
26
27
...
»

Summary of Contents for MELSEC iQ-F FX55-ASL-M

































































































Reviews:

No comments

Related manuals for MELSEC iQ-F FX55-ASL-M

Brand: Gardena Pages: 100

Brand: IBM Pages: 72

Brand: FAAC Pages: 32

Brand: Jabra Pages: 4

Brand: Taco Electronic Solutions Pages: 28

Brand: U.S. Divers Pages: 22

FT-2000 - MENU MODE LIST

Brand: Yaesu Pages: 56

DuetPro Carrycot

Brand: Qtus Pages: 52

Tunnel Master Jr

Brand: ICS Pages: 70

Brand: Black Stone Pages: 2

Brand: GIESSE Pages: 136

BALBOA CS6000B Series

Brand: HydroQuip Pages: 32

GAT Access 6600 Series

Brand: Gantner Pages: 4

Brand: ICP DAS USA Pages: 6

ServLink ACR3500A

Brand: Black Box Pages: 115

GLOFA G7M-DR20U

Brand: LS Industrial Systems Pages: 367

Brand: Polaroid Pages: 14

Hauser COMPAX-M Series

Brand: Parker Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands