manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-F FX55-ASL-M, User Manual

Share
Download
Mitsubishi Electric MELSEC iQ-F FX55-ASL-M User Manual Download Page 65

8  PROGRAMMING

8.2  Communication of FX5-ASL-M with Slave Module

63

8

Settings of the slave module

Write addresses to slave modules to register the FX5-ASL-M.

Address setting

Write addresses to slave modules with an address writer.
 • Output ASLINKER: Address 0 (ID: 0000H)
 • Input ASLINKER: Address 0 (ID: 0200H)

Automatic address detection

Keep pressing the SET switch on the FX5-ASL-M until the SET LED turns on.
When the SET LED flashes and then turns off, it indicates that the registration of IDs (addresses) has been completed.

Checking the system status

Check whether the FX5-ASL-M can communicate with the slave modules normally.
The following LED statuses indicate that the communication is established normally.
 • LED of the FX5-ASL-M

 • LED of the ASLINKER

LED

Status

POWER

On

RUN

On

ERROR

Off

LINK

Flashing

SET

Off

ALM

Off

LED

Status

LINK LED

Flashing

Other than the LINK LED

Off

Summary of Contents for MELSEC iQ-F FX55-ASL-M

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands