manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-F FX55-ASL-M, User Manual

Share
Download
Mitsubishi Electric MELSEC iQ-F FX55-ASL-M User Manual Download Page 51

6  WIRING

6.6  Connecting Slave Module or Terminating Unit

49

6

6.6

Connecting Slave Module or Terminating Unit

Connection type

 • The maximum transmission distance in an AnyWireASLINK stand-alone system is 200 m, which is the overall cable 

distance including the main line and branch line. (It varies depending on the wire diameter of the transmission cables (DP, 
DN) or the transmission cable supply current.)

 • AnyWireASLINK systems support tree branch connection, T-branch connection, and multidrop connection.
 • Up to 128 slave modules can be connected.

The total length of the transmission distance for the AnyWireASLINK system can be calculated from A + B + 
C.
Note that the total length should not exceed the maximum transmission distance or the total length set for the 
system to branch lines.

(1) Tree branch connection
(2) T-branch connection

A

B

(1)

C

(2)

Summary of Contents for MELSEC iQ-F FX55-ASL-M

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands