Mitsubishi Electric MELSEC iQ-F FX55-ASL-M User Manual Download Page 20

Page: 20 / 96

2 SPECIFICATIONS
2.4 Part Names

2.4

Part Names

This chapter describes the names of each part of the FX5-ASL-M.

No.

Name

Description

[1]

Transmission cable terminal block

A terminal block of the AnyWireASLINK

[2]

Extension cable

Cable for connecting the module when adding the FX5-ASL-M

[3]

SET switch

Switch for automatic detection of the slave module ID (address)

[4]

Direct mounting hole

Screw holes (2-



4.5, mounting screw: M4 screw) for direct installation

[5]

Operation status display LEDs

Indicates the operating status of the module. (



Page 19 LED display)

[6]

Extension connector (for next
module)

Connector for connecting the extension cable of an extension module.

[7]

Name plate

The product model name, manufacturer's serial number etc. are shown.

[8]

DIN rail mounting groove

The module can be installed on DIN46277 rail (35 mm wide).

[9]

DIN rail mounting hook

Hook for mounting the module on a DIN rail of DIN46277 (35 mm wide).

[10]

Pullout tab

They are used when drawing out an extension cable.

[1]

[10]

[2]

[4]

[3]

[8]

[7]

[9]

[5]

[6]

Summary of Contents for MELSEC iQ-F FX55-ASL-M

































































































Search results

Summary of Contents for MELSEC iQ-F FX55-ASL-M

Reviews:

Related manuals for MELSEC iQ-F FX55-ASL-M

Brands by name

Popular brands

Mitsubishi Electric MELSEC iQ-F FX55-ASL-M, User Manual

Search results

Summary of Contents for MELSEC iQ-F FX55-ASL-M

Reviews:

Related manuals for MELSEC iQ-F FX55-ASL-M

Brands by name

Popular brands