Mitsubishi Electric MELSEC iQ-F FX55-ASL-M User Manual Download Page 67

Page: 67 / 96

9 TROUBLESHOOTING

9.1 Checking with LED

TROUBLESHOOTING

This chapter describes troubleshooting of the FX5-ASL-M.

9.1

Checking with LED

This section describes troubleshooting using LED.

When the POWER LED turns off

When the POWER LED turns off after powering on the FX5-ASL-M, check the following.

When the RUN LED turns off

When the RUN LED turns off after powering on the FX5-ASL-M, check the following.

When the ERROR LED turns on

When the ERROR LED turns on, check the following.

When the LINK LED turns on or off

When the LINK LED turns on or off, check the following.

When the ALM LED is flashing at 0.2 second intervals

When the ALM LED is flashing at 0.2 second intervals, check the following.

Check item

Action

Is the FX5-ASL-M mounted correctly?

Securely mount the FX5-ASL-M on the CPU module.

Check item

Action

Is the FX5-ASL-M mounted correctly?

Securely mount the FX5-ASL-M on the CPU module.

Check item

Action

Does a programmable controller error occur in the GX Works3?

Confirm the details of the 'Latest error code storage area' (Un\G10256) with
the GX Works3 buffer memory monitor, and process accordingly.

Check item

Action

Does a programmable controller error occur in the GX Works3?

Confirm the details of the 'Latest error code storage area' (Un\G10256) with
the GX Works3 buffer memory monitor, and process accordingly.

Check item

Action

Is the power supply voltage of the 24 V DC external power supply within the
rated value?

Adjust the power supply voltage of the 24 V DC external power supply within
the rated value (21.6 to 27.6 V DC). (The recommended voltage is 26.4 V
DC.)

Is any power cable short-circuited?

• Check that the power cables (24V, 0V) are not disconnected or short-

circuited.

• When crimping the link connector, check that the pin layout is correct.

Is the terminal block properly wired?

• Check that the 24 V DC external power supply is properly connected to the

terminal blocks of the FX5-ASL-M and the slave module.

• Check that there is no short circuit or incorrect wiring and screws are

tightened sufficiently.

Summary of Contents for MELSEC iQ-F FX55-ASL-M

































































































Search results

Summary of Contents for MELSEC iQ-F FX55-ASL-M

Reviews:

Related manuals for MELSEC iQ-F FX55-ASL-M

Brands by name

Popular brands

Mitsubishi Electric MELSEC iQ-F FX55-ASL-M, User Manual

Search results

Summary of Contents for MELSEC iQ-F FX55-ASL-M

Reviews:

Related manuals for MELSEC iQ-F FX55-ASL-M

Brands by name

Popular brands