Mitsubishi Electric MELSEC iQ-F FX55-ASL-M User Manual Download Page 50 | Manualshive

Page: 50 / 96

background image

48

6 WIRING
6.4 Wiring Precautions

6.4

Wiring Precautions

• Do not run multiple transmission cables (DP, DN) using a multicore cable.

• The voltage should not fall below the lower limit of the allowable voltage range due to voltage drop caused by the cable. If

the voltage falls below the lower limit, malfunctions may occur.

• Do not connect soldered cables directly to the terminals. Doing so may loosen the screws, resulting in a poor contact.
• In the AnyWireASLINK system, signals and power are supplied to a slave module with two transmission cables: DP and

DN. Therefore, use a stranded wire of 1.25



or larger as the main line.

• General-purpose wire, cabtyre cable and flat cable, etc. can be used.
• Use a crimping tool to connect a wire ferrule to a cable.
• Before inserting a wire ferrule, check the shapes of the wire insertion opening and wire ferrule. Then, insert the terminal in

the correct orientation. A wire ferrule wider than the wire insertion opening may damage the terminal block. (

• Signal names are not printed on the transmission cable terminal block. To avoid incorrect wiring, wire cables to the terminal

block attached to the FX5-ASL-M.

• Do not insert multiple wire ferrules into one wire insertion opening. Doing so may cause damage on the terminal block or

cable, or malfunction.

6.5

Power Supply/grounding Wiring

Power supply/grounding wiring

Grounding

Perform the following.
• Perform class D grounding. (Grounding resistance: 100



or less)

• Ground the PLC independently if possible.
• If the PLC cannot be grounded independently, perform the "Shared grounding" shown below.

• Bring the grounding point close to the PLC as much as possible so that the ground cable can be shortened.

DP
DN
DP
DN

DP
DN
DP
DN

Grounding

(Grounding

resistance:

100



or less)

Grounding

(Grounding

resistance:

100



or less)

0V LG

24V

FX5U CPU module

24 V DC

FX5-ASL-M

IN

PLC

Other

equipment

Other

equipment

Other

equipment

PLC

PLC

Shared grounding

(Good condition)

Common grounding

(Not allowed)

Independent grounding

(Best condition)

«
...
48
49
50
51
52
...
»

Summary of Contents for MELSEC iQ-F FX55-ASL-M

































































































Reviews:

No comments

Related manuals for MELSEC iQ-F FX55-ASL-M

Brand: Eaton Pages: 166

Brand: Gardena Pages: 16

Brand: MADRIX Pages: 28

Brand: tams elektronik Pages: 12

Brand: MAKOT Pages: 6

Brand: Omnex Pages: 9

Brand: Omegon Pages: 6

Brand: WATERLOO Pages: 8

Brand: VAT Pages: 39

Brand: Samson Pages: 124

Brand: Samson Pages: 86

Brand: VAC Pages: 5

Brand: Zamel Pages: 23

Brand: Zamel Pages: 2

Brand: Zamel Pages: 2

Brand: Zander Aachen Pages: 44

Extra Free ROB-01/12-24V

Brand: Zamel Pages: 2

Brand: Zamel Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands