Mitsubishi Electric MELSEC iQ-F FX55-ASL-M User Manual Download Page 49

Page: 49 / 96

6 WIRING

6.3 Wiring Product

6.3

Wiring Product

Applicable wires and cables

Use the following wires or cables connected to the transmission cable terminal block.

Wire ferrule

Bare cables can be connected to the transmission cable terminal block; however, for safety reasons, it is recommended to
connect wire ferrules.
Use UL-listed wire ferrules and, for processing, use a tool recommended by their manufacturer.

Classification

Name

Wire size

Temperature rating

Transmission cable (DP, DN)

UL-listed general-purpose 2-wire cable (VCTF, VCT)

1.25





or higher

0.75



UL-listed general-purpose wire

1.25



0.75



Dedicated flat cable

1.25





0.75



Power supply cable (24V, 0V)

UL-listed general-purpose 2-wire cable (VCTF, VCT)

0.75



to 2.0





or higher

UL-listed general-purpose wire

0.75



to 2.0



Dedicated flat cable

1.25





0.75



Type

Model

Application

Contact

Wire ferrule

AI 0,75-10 GY

Processing of a 0.75



wire

PHOENIX CONTACT GmbH & Co. KG

AI 1,5-10

Processing of a 1.25



wire

Summary of Contents for MELSEC iQ-F FX55-ASL-M

































































































Search results

Summary of Contents for MELSEC iQ-F FX55-ASL-M

Reviews:

Related manuals for MELSEC iQ-F FX55-ASL-M

Brands by name

Popular brands

Mitsubishi Electric MELSEC iQ-F FX55-ASL-M, User Manual

Search results

Summary of Contents for MELSEC iQ-F FX55-ASL-M

Reviews:

Related manuals for MELSEC iQ-F FX55-ASL-M

Brands by name

Popular brands