manualshive.com logo in svg

Mitsubishi Electric FDF100VNVD, Technical Manual

The Mitsubishi Electric FDF100VNVD Technical Manual is a comprehensive user guide that provides detailed instructions and specifications for optimal usage of the product. This manual is available for free download at manualshive.com, ensuring easy access to the essential information necessary for efficient operation and maintenance of the FDF100VNVD.

Share
Download
background image

-

 61 

-

-

 61 

-

 '11 • PAC-T-160

Security instructions

CAUTION

WARNING

●

●

●

●

●

●

●

Do not mingle solid cord and stranded cord on power source and signal side 
terminal block.

In addition, do not mingle difference capacity solid or stranded cord.
Inappropriate cord setting could cause loosing screw on terminal block, bad electrical 
contact, smoke and fire.

●

●

●

●

●

●

●

●

●

●

PGAO12D405

●

●

●

●

Electrical wiring work must be performed by an electrician qualified by a local power provider according to 
the electrical installation technical standards and interior wiring regulations applicable to the installation site.

Be sure to have the electrical wiring work done by qualified electrical installer, 
and use exclusive circuit.

Power source with insufficient capacity and improper work can cause electric shock and fire.

Use specified wire for electrical wiring, fasten the wiring to the terminal securely, 
and hold the cable securely in order not to apply unexpected stress on the terminal.

Loose connections or hold could result in abnormal heat generation or fire.

Arrange the electrical wires in the control box properly to prevent them from 
rising. Fit the lid of the services panel property.

Improper fitting may cause abnormal heat and fire.

Use the genuine optional parts. And installation should be performed by a 
specialist.

If you install the unit by yourself, it could cause water leakage, electric shock and fire.

Turn off the power source during servicing or inspection work.

If the power is supplied during servicing or inspection work, it could cause electric 
shock and injury by the operating fan.

Perform earth wiring surely.

Do not connect the earth wiring to the gas pipe, water pipe, lightning rod and telephone earth  
wiring. Improper earth could cause unit failure and electric shock due to a short circuit. 

Make sure to install earth leakage breaker on power source line. 
(countermeasure thing to high harmonics.)

Absence of breaker could cause electric shock.

Do not use any materials other than a fuse of correct capacity where a fuse 
should be used.

Connecting the circuit by wire or copper wire could cause unit failure and fire.

Do not turn off the power source immediately after stopping the operation.

Be sure to wait for more than 5 minutes. Otherwise it could cause water leakage or 
breakdown.

Do not control the operation with the circuit breaker.

It could cause fire or water leakage. In addition, the fan may start operation 
unexpectedly and it may cause injury.

Do not repair by yourself. And consult with the dealer about repair.

Improper repair may cause water leakage, electric shock or fire.

Consult the dealer or a specialist about removal of the air conditioner.

Improper installation may cause water leakage, electric shock or fire.

Shut off the power before electrical wiring work.

It could cause electric shock, unit failure and improper running.

Use the circuit breaker of correct capacity. Circuit breaker should be the one 
that disconnect all poles under over current.

Using the incorrect one could cause the system failure and fire.

Earth leakage breaker must be installed.

If the earth leakage breaker is not installed, it can cause electric shocks.

Use power source line of correct capacity.

Using incorrect capacity one could cause electric leak, abnormal heat generation and fire.

Read the “SAFETY PRECAUTIONS” carefully first of all and then strictly follow it during the 
installation work in order to protect yourself.
The precautionary items mentioned below are distinguished into two levels,                     
and                    .
                    :  Wrong installation would cause serious consequences such as injuries or death.
                    :  Wrong installation might cause serious consequences depending on circumstances.
Both mentions the important items to protect your health and safety so strictly follow 
them by any means.
The meanings of “Marks” used here are as shown on the right:

Accord with following items. Otherwise, there will be the risks of electric shock and
fire caused by overheating or short circuit.

Never do it under any circumstances.

CAUTION

CAUTION

Always do it according to the instruction.

Electrical Wiring Connection

②

Wiring for the remote controller (Continued)

②

Wiring for the remote controller

③

Function Setting by Remote Controller

③

Function Setting by Remote Controller (Continued)

Power source

Cable connection for single unit installation

Cable connection for a V multi configuration installation

Three-phase model

Single-phase model

Method of setting Master/Slave of indoor unit

Switch and wiring specification

(Factory setting: “Master”)

Refer to the installation manual attached to the outdoor unit. 

PCB

SW

SW5-1

OFF

OFF

OFF

ON

ON

ON

ON

OFF

SW5-2

 

①②③

①②③             

①②③ 

①②③ 

L  N

Remote controller

Remote controller

Remote controller

controller line

Power source line

Indoor-Outdoor

Power source

Circuit breaker

Indoor Unit

Indoor Unit

Master

Slave 1

Slave 2

Slave 3

①②③ 

①②③ 

L1 L2 L3  N

Master

Slave 1

Twin type 

①②③

Remote controller line (no polarity)

AIR CON NO.

Outdoor Unit

Indoor Unit

Indoor Unit

Outdoor Unit

Indoor Unit

Outdoor Unit

Earth

Earth

Earth

Earth

Earth

Earth

Earth

Earth leakage

breaker

Power source

●

Use three-core cable as wiring between indoor and outdoor unit. As for detail, refer to "INSTALLATION MANUAL" of 

outdoor Unit.

●

Set earth of D-type.

●

Keep "remote controller line" and "power source line" away from each other on constructing of unit outside.

●

Run the lines (power source, remote controller and "between indoor and outdoor unit") upper ceiling through iron 

pipe or other tube protection to avoid the damage by mouse and so on.

●

Do not add cord in the middle of line route (of power source, remote controller and "between indoor and outdoor 

unit") on outside of unit. If connecting point is flooded, it could cause problem as for electric or communication. (In 
the case that it is necessary to set connecting point on the way, perform thorough waterproof measurement.)

●

Do not connect the power source line [220V/240V/380V/415V] to signal side terminal block. Otherwise, it could 

cause failure.

●

Screw the line to terminal block without any looseness, certainly.

●

Do not turn on the switch of power source, before all of line work is done.

●

Connection of the line ("Between indoor and outdoor unit", Earth and Remote controller)

①

Remove lid of control box before connect the above lines, and connect the lines to terminal block according to 
number pointed on label of terminal block. 
In addition, pay enough attention to confirm the number to lines, because there is electrical polarity except earth 
line. Furthermore, connect earth line to earth position of terminal block of power source.

②

Install earth leakage breaker on power source line. In addition, select the type of breaker for inverter circuit as 

earth leakage breaker.

③

If the function of selected earth leakage breaker is only for earth-fault protection, hand switch (switch itself and 
type "B" fuse) or circuit breaker is required in series with the earth leakage breaker.

④

Install the local switch near the unit.

 ① 

Open the remote controller cover and remove the screw without fail.

 ② 

Remove the upper case of remote controller. Attach a flat head screwdriver at the upper part of remote controller 

and pry lightly. It will come off easily.
Use some cushion to protect the center panel.

①

As for connecting method of power source, select from following connecting patterns.  In principle, do not directly connect 

power souce line to inside unit.

As for exceptional connecting method of power souce, discuss with the power provider of the country with referring to 
technical documents, and follow its instruction.

②

For cable size and circuit breaker selection, refer to the outdoor unit installation manual.

①

Connect the same pairs number of terminal block "

①,②,

and

③

"and "  X  and  Y  " between master and slave 

indoor units.

②

Do the same address setting of all inside units belong to same refrigerant system by rotary switch SW2 on indoor 

unit's PCB (Printed circuit board).

③

Set slave indoor unit as "slave 1" through "slave 3" by address switch SW5-1, 5-2 on PCB.

④

When the                        button on the remote control unit is pressed after turning on the power, an indoor unit's address 

number will be displayed. Do not fail to confirm that the connected indoor unit's numbers are displayed on the remote 
control unit by pressing the        or         button.

Circuit breaker

r

k

Circuit breaker

Earth leakage breaker

Connecting line

Remote

controller line

Power source line

Indoor-Outdoor

Connecting line

Remote

Installation and wiring of remote controller

①

Wiring of remote controller should use 0.3mm

2

× 2 core wires or cables. (on-site configuration)

②

Maximum prolongation of remote controller wiring is 600 m.

If the prolongation is over 100m, change to the size below.
But, wiring in the remote controller case should be under 0.5mm

2

 . Change the wire size outside of the case 

according to wire connecting. Waterproof treatment is necessary at the wire connecting section. Be careful about 
contact failure.

The indication when power source is supplied

How to set function

When power source is turned on, the following is displayed on the remote controller until the  

communication between the remote controller and indoor unit settled.

At the same time, a mark or a number will be displayed for two seconds first.
This is the software's administration number of the remote controller, not an error cord.

When remote controller cannot communicate with the indoor unit for half an hour, the below indication willappear.
Check wiring of the indoor unit and the outdoor unit etc.

100 - 200m.........................0.5mm

2

s

 2 cores

Under 300m  .......................0.75mm

2

s

 2 cores

Under 400m  .......................1.25mm

2

s

 2 cores

Under 500m  .......................2.0mm

2

s

 2 cores

Master remote controller : "                               "
Slave remote controller : "                               "

The left mark is only an 

example. Other marks may 

appear.

Screw

(View after removing the cover)

Terminal setting SW

Press         or         button.

Make sure which do you want to set, "     FUNCTION     " (remote 
controller function) or "I/U FUNCTION     " (indoor unit function).

2.

1.

3.

4.

5.

Stop air-conditioner and press              (SET)              (MODE) buttons at 
the same time for over three seconds, and the "FUNCTION SET      " 
will be displayed.

Press              (SET) button.

Selecct "     FUNCTION      "  (remote controller function) or "I/U FUNCTION     " (indoor unit function).

Press              (SET) button.

6.

"DATA LOADING" (Indication with blinking)

Display is changed to "01 GRILLE      SET".

"DATA LOADING" (Blinking for 2 to 23 seconds to read the data)

(1)

Press              (SET) button.

On the occasion of remote controller function selection

On the occasion of indoor unit function selection

Press         or         button.
"No. and function"are indicated by turns on the remote controller function table, then you can select from them.
(For example)

Press         or         button.
Select the setting.

The current setting of selected function is indicated.
(for example) "AUTO RUN ON"       If "02 AUTO RUN SET" is selected

Press              (SET) button.
"SET COMPLETE" will be indicated, and the setting will be completed.
Then after "No. and function" indication returns, Set as the same procedure if you want to set continuously ,and if to finish, go to 7.

Indication is changed to "02 FAN SPEED SET".    Go to      .

[Note]

If plural indoor units are connected to a remote controller, 
the indication is "I/U 000" (blinking)       The lowest number of the indoor unit connected is indicated.

Setting

Function No.

Function

Operation message
Function description:      , 
setting description:

Function No.

Fixing button

Finishing button

7

2

1

6

Starting button

Previous screen button

Indoor unit selection button

Earth leakage breaker

Earth leakage breaker

The initial function setting for typical using is performed automatically by the indoor unit connected, when remote 
controller and indoor unit are connected.
As long as they are used in a typical manner, there wiil be no need to change the initial settings.
If you would like to change the initial setting marked “      ”, set your desired setting as for the selected item.
The procedure of functional setting is shown as the following diagram.

Sequence of the function setting is as follows.

When shipped, the range of set temperature differs depending on the operation mode as below.

Heating : 16~30ûC (55~86ûF)
Except heating (cooling, fan, dry, automatic) : 18~30ûC (62~86ûF)

Upper limit and lower limit of set temperature can be changed with remote controller.

Upper limit setting: valid during heating operation.  Possible to set in the range of 20 to 30ûC (68 to 86ûF).
Lower limit setting: valid except heating (automatic, cooling, fan, dry) Possible to set in the range of 18 to 26ûC (62 to
79ûF).
When you set upper and lower limit by this function, control as below.

1.  When      TEMP RANGE SET, remote controller function of function setting mode is "INDN CHANGE" (factory setting),

During heating, you cannot set the value exceeding the upper limit.

During operation mode except heating, you cannot set the value below the lower limit.

2.  When      TEMP RANGE SET, remote controller function of function setting mode is "NO INDN CHANGE"

During heating, even if the value exceeding the upper limit is set, upper limit value will be sent to the indoor unit.
But, the indication is the same as the temperature set.

During except heating, even if the value lower than the lower limit is set, lower limit value will be sent to the indoor unit.
But, the indication is the same as the temperature set.

How to set upper and lower limit value

1.    Stop the air-conditioner, and press             (SET) and              (MODE) button at the same time for over three 
       seconds .

The indication changes to "FUNCTION SET      ".

2.    Press        button once, and change to the "TEMP RANGE      " indication.
3.    Press             (SET) button, and enter the temperature range setting mode.
4.    Select  "UPPER LIMIT      " or "LOWER LIMIT     " by using               button.
5.    Press            (SET) button to fix.
6.    When "UPPER LIMIT      " is selected (valid during heating)

Press            (SET) button to fix. Indication example: "UPPER 26ûC" (Displayed for two seconds)
After the fixed upper limit value displayed for two seconds, the indication will return to "UPPER LIMIT      ".

7.    When "LOWER LIMIT      " is selected (valid during cooling, dry, fan, automatic)

Indication: "              SET UP"       "LOWER 18ûC     "

8.    Press  ON/OFF  button to finish.

Previous button

If upper limit value is set

If upper limit value is set

If lower limit value is set

If lower limit value is set

Indication: "              SET UP"       "UPPER 30ûC     "
Select the upper limit value with temperature setting button             . Indication example: "UPPER 26ûC        "
(blinking)

Select the lower limit value with temperature setting button             . Indication example: "LOWER 24ûC        " 
(blinking)

 Press            (SET) button to fix. Indication for example: "LOWER 24ûC" (Displayed for two seconds)

After the fixed lower limit value displayed for two seconds, the indication will return to "LOWER LIMIT       ".

It is possible to finish by pressing 
 ON/OFF  button on the way, but 
unfinished change of setting is 
unavailable.
During setting, if you press
(RESET) button, you return to the 
previous screen.

Note 2: As for plural indoor unit, set indoor functions to each master and slave indoor unit.
            But only master indoor unit is received the setting change of indoor unit function “05 EXTERNAL 
            INPUT” and “06 PERMISSION / PROHIBISHION”.

Note 1: Fan setting of “HIGH SPEED”

Initial function setting of some indoor unit is “HIGH SPEED”

STANDARD

FAN SPEED SET

Fan tap

HIGH SPEED1, 2

UH - Hi 

UH - Me

UH - Hi - Me 

Hi - Lo

Hi - Me

Hi - Me - Lo

UH - UH - Hi - Me

UH - Hi - Me - Lo

Indoor unit air flow setting

-

-

-

-

-

-

-

The functional setting

The range of temperature setting

●

For each indoor unit, one more remote controller can be connected in addition to the one which is built in the main 

unit.

Set SW1 to "Slave" for the slave remote controller. It was factory set to "Master" for shipment.

Note: The setting "Remote controller thermistor enabled" is only selectable with the master remote controller in the position where you 

want to check room temperature.

The air conditioner operation follows the last operation of the remote controller regardless of the master/ slave setting of it.

Remote controller cord (no polarity)

Remote controller

SW1 "Master"

Switch

Setting

Contents

M

Master remote controller

SW1

S

Slave remote controller

Remote controller

SW1 "Slave"

Lower

Master

Slave

Upper

Board

Indoor units

* When setting the remote controller built in the main unit to the “Slave”:
  Remove the cover and change the setting of switch as follows.

It is possible to finish by pressing  ON/OFF  button on the way, but unfinished change of setting is unavailable.
During setting, if you press              (RESET) button, you return to the previous screen.
Setting is memorized in the controller and it is saved independently of power failure.

How to check the current setting

When you select  from "No. and funcion" and press set button by the previous operation,  the "Setting" displayed first is the current 
setting.
(But, if you select "ALL UNIT      ", the setting of the lowest number indoor unit is displayed.)

7.

Press         or         button.
Select the setting.

Press              (SET) button.

Press   ON/OFF   button.

Setting is finished.

The current setting of selected function is indicated.
(For example) "STANDARD"       If "02 FAN SPEED SET" is selected.

Press              (SET) button.

"SET COMPLETE" will be indicated, and the setting will be completed. 
Then after "No. and function" indication returns, set as the same procedure if you want to set continuously , and if to finish, go to 7.

When plural indoor units are connected to a remote controller, press the   AIRCON NO.  button, which allows you to go back to the
indoor unit selection screen. (example "I/U 000     ")

Setting

(2)

(3) Press              (SET) button.

Press         or         button.

Press         or         button.

Select the number of the indoor unit you are to set
If you select "ALL UNIT      ", you can set the same setting with all unites.

"No. and function" are indicated by turns on the indoor unit function table, then you can select from them.
(For example)

Function No.
Function

①

⑤

④

③

②

①

②

③

④

⑤

Summary of Contents for FDF100VNVD




















































































































































































































Reviews:

No comments

Related manuals for FDF100VNVD

GE AJEM12DCD Owner'S Manual & Installation Instructions preview
AJEM12DCD
Brand: GE Pages: 72
Haier AW07LC2VHA Technical Overview preview
AW07LC2VHA
Brand: Haier Pages: 122
Panasonic CS-KS30NKU Technical & Service Manual preview
CS-KS30NKU
Brand: Panasonic Pages: 108
Panasonic CS-A12PKD Service Manual preview
CS-A12PKD
Brand: Panasonic Pages: 140
Valeo Citysphere S Installation Instructions Manual preview
Citysphere S
Brand: Valeo Pages: 15
Daikin FTXTM30R2V1B User Reference Manual preview
FTXTM30R2V1B
Brand: Daikin Pages: 60
Daikin FTXP50M2V1B Operation Manual preview
FTXP50M2V1B
Brand: Daikin Pages: 12
Daikin FTXN15KVJU Operation Manual preview
FTXN15KVJU
Brand: Daikin Pages: 30
Daikin FTXF20C5V1B Operation Manual preview
FTXF20C5V1B
Brand: Daikin Pages: 16
Daikin FTYN25LV1B Installation Manual preview
FTYN25LV1B
Brand: Daikin Pages: 25
Daikin FTYN25GXV1B Service Manual preview
FTYN25GXV1B
Brand: Daikin Pages: 97
Daikin FTHF40RVLT Operation Manual preview
FTHF40RVLT
Brand: Daikin Pages: 64
Daikin FTXN25KEV1B Service Manual preview
FTXN25KEV1B
Brand: Daikin Pages: 158
Daikin FTXC20BV1B Installation Manual preview
FTXC20BV1B
Brand: Daikin Pages: 320
Daikin FTXP20M5V1B Installation Manual preview
FTXP20M5V1B
Brand: Daikin Pages: 116
Daikin FTXF20D5V1B Installer'S Reference Manual preview
FTXF20D5V1B
Brand: Daikin Pages: 56
Daikin FTXS20K2V1B Operation Manual preview
FTXS20K2V1B
Brand: Daikin Pages: 44
Daikin FTXN09KEVJU Operation Manual preview
FTXN09KEVJU
Brand: Daikin Pages: 178

Brands by name

Popular brands

Load more brands