Mitsubishi Electric FDF100VNVD Technical Manual Download Page 198

Page: 198 / 211

–

196

–

'11 • PAC-T-160

E60

Compressor rotor lock error

(Models FDC200, 250 only)

1. Applicable model

5. Troubleshooting

Models FDC200, 250

Diagnosis

Countermeasure

Is the

power supply voltage

OK?

Reset the power supply and restart operation.

YES

Does the compressor start?

Does E59 occur?

YES

Does it

start up normally without

recurrence of

E60.

YES

Does the

compressor run without

occurrence of

E42?

YES

Is the noise

or vibration of compressor

normal?

Is the

output from inverter

checker OK?

YES

Check and correct the

power supply voltage

Correct it based on the

troubleshooting of E59

Correct it based on the

troubleshooting of E42

Defective inverter PCB

➞

Replace.

replace also the power

transistor module.

Replace compressor.

Check compressor for

insulation, resistance.

Replace compressor if

necessary.

Defective inverter PCB

➞

Replace.

replace also the power

transistor module.

2. Error detection method

Compressor rotor position

3. Condition of Error displayed

If it fails again to detect the

rotor position after shifting to

the compressor rotor position

detection operation, the

compressor stops.

When it is restart

automatically after 3 minutes,

it is detected 4 times within 15

minutes.

4. Presumable cause

• Defective outdoor fan motor

• Defective outdoor control

PCB

• Defective inverter PCB

• Anomalous power supply

voltage

• Improper refrigerant amount

and refrigerant circuit

• Defective compressor (motor,

bearing)

Note: Insulation resistance

• The unit is left for long period without power supply or soon after installation, migrated liquid refrigerant may dissolve in the refrigerant oil in the compressor.

In such case insulation resistance decreases upto several M

or lower. If the electric leakage breaker is activated due to low insulation resistance, check followings.

➀

Check whehter the insulation resistance can recover or not, ater 6 hours has passed since power ON.

(By energize the crankcase heater, migrated liquid refrigerant in the refrigerant oil in compressor can be evaporated)

➁

Check whether the electric leakage breake conforms to high-hermonic specifications

(As units has inverter, in order to prevent from improper operation, be sure to use high-hermonic one.)

Error code

Remote controller:

LED

Green

Red

Outdoor

Content

Indoor Keeps flashing

Keeps flashing

Stays OFF

time flash

Note (1) Value in

are for the Models SRC40 ~ 60.

Summary of Contents for FDF100VNVD




















































































































































































































Search results

Summary of Contents for FDF100VNVD

Reviews:

Related manuals for FDF100VNVD

Brands by name

Popular brands

Mitsubishi Electric FDF100VNVD, Technical Manual

Search results

Summary of Contents for FDF100VNVD

Reviews:

Related manuals for FDF100VNVD

Brands by name

Popular brands