Mitsubishi Electric FDF100VNVD Technical Manual Download Page 206

Page: 206 / 211

204

'11 • PAC-T-160

Simple Remote Controller Installation Manual

Read together with indoor unit's installation manual.

WARNING

●

Fasten the wiring to the terminal securely and hold the cable securely so as not to apply

unexpected stress on the terminal.

Loose connection or hold will cause abnormal heat generation or fire.

●

Make sure the power supply is turned off when electric wiring work.

Otherwise, electric shock, malfunction and improper running may occur.

CAUTION

●

DO NOT leave the remote controller without the upper case.

In case the upper cace needs to be detached, protect the remote controller with a packaging box
or bag in order to keep it away from water and dust.

●

DO NOT install the remote controller at the following places in order to avoid malfunction.

(1) Places exposed to direct sunlight

(4) Hot surface or cold surface enough to generate condensation

(2) Places near heat devices

(5) Places exposed to oil mist or steam directly

(3) High humidity places

(6) Uneven surface

Accessories

Remote controller, wood screw (

3.5

16) 2 pieces

Prepare on site

Remote controller cord (2 cores) (Refer to [2. Installation and wiring of remote controller])

[In case of embedding cord] Electrical box, M4 screw (2 pieces)

[In case of exposing cord] Cord clamp (if needed)

Installation procedure

In case of embedding cord

⑴

Make certain to remove the screw on the bottom
surface of the remote controller.

⑵

Remove the upper case of the remote controller.

Insert a flat-blade screwdriver to a concave portion of the bottom
surface of the remote controller and slightly twist it, and the case is
removed.

⑶

Pre-bury the electrical box and remote controller cord.

⑷

Prepare two M4 screws (recommended length: 12 – 16mm), and install the lower case to the electrical box.

Do not use a screw whose screw head is larger than the height of the wall around the screw hole.

⑸

Connect the remote controller cord to the terminal block.

Connect the terminals (X and Y) of the remote controller and the terminals (X and Y) of the indoor
unit. (No polarity of X and Y)

⑹

Mount the upper case for restoring to its former state so as not to crimp the remote controller cord,
and secure with the removed screw.

In case of exposing cord

⑴

Make certain to remove a screw on the bottom surface of the
remote controller.

⑵

Remove the upper case of the remote controller.
Insert a flat-blade screwdriver to a concave portion of
the bottom surface of the remote control and slightly
twist it, and the case is removed.

⑶

The remote controller cord can be extracted from the
upper center.
After the thin part in the upper side of the remote
controller upper case is scraped with a nipper or knife,
remove burr with a file.

⑷

The lower case of the remote controller is mounted to
a flat wall with two accessory wood screws.

⑸

Connect the remote controller cord to the terminal block.
Connect the terminals (X and Y) of the remote controller and
the terminals (X and Y) of the indoor unit. (No polarity of X and
Y)
The wiring route is as shown in the right.

The wiring in the remote controller case should be 0.3 mm

(recommended) to 0.5 mm

maximum.
Further, peel off the sheath.
The peeling length of each wiring is as follows:

X wiring : 160mm
Y wiring : 150mm

⑹

Mount the upper case for restoring to its former state so as not to
crimp the remote controller cord, and secure with the removed screw.

⑺

In the case of exposing installation, secure the remote controller cord to the wall surface with a
cord clamp so as not to loosen the remote controller cord.

Installation and wiring of remote controller

⑴

Wiring of remote controller should use 0.3mm

× 2 core wires or cables. (on-site configuration)

⑵

Maximum prolongation of remote controller wiring is 600 m.
If the prolongation is over 100m, change to the size below.
But, the wiring in the remote controller case should be 0.3mm

(recommended) to 0.5mm

Change the wire size outside of the case according to wire connecting. Waterproof treatment is
necessary at the wire
connecting section. Be careful about contact failure.
100 - 200m

･････････････････

0.5mm

× 2 cores

Under 300m

･････････････････

0.75mm

× 2 cores

Under 400m

･････････････････

1.25mm

× 2 cores

Under 600m

･････････････････

2.0mm

× 2 cores

⑵

Set the switch SW1-1 of the slave remote controller is “Slave” (ON). The factory default is set as “Master” (OFF).

(Note) • The remote controller thermistor enabled setting can be set only to the master remote controller.

• Install the master remote controller at the position to detect room temperature.
• The air conditioner operation follows the last operation of the remote controller in case of the

master / slave setting.

Master/ slave setting when more than one remote controller are used

⑴

Up to two remote controllers can be connected to one unit (or one group) of indoor unit.

The indication when power source is supplied

⑴

At the time of turning the power source on, after the light is on for the first 2 seconds, the display

becomes as shown below.

The number displayed on the upper side of LCD in the remote control is the software number,

and this is not an error code.

⑵

Then, “88.0 °C” blinks on the remote controller until the communication between the remote

controller and the indoor unit is established.

⑶

In the case of connecting one remote controller with one unit (or one group) of indoor unit, make

certain to set the master remote controller (factory default).

If the slave remote control is set, a communication cannot be

established.

⑷

If a state where the communication between the remote

controller and the indoor unit cannot be established continues

about for 30 minutes, “E” is displayed. Confirm the wiring of

the indoor unit and the outdoor unit and master/slave setting of

the remote controller.

Confirmation method for return air temperature

Return air temperature can be confirmed by the remote controller operation.

⑴

Press AIR CON NO. button for over 5 seconds.

“88” blinks on the temperature setting indicator.
(“88” blinks for approximately 2 seconds while data is read.)

↓

Then, the return air temperature is displayed.
(Example) return air temperature: “27 °C” (blinking)
(Note) For the return air temperature, in the normal case, the return air temperature of the indoor

unit is displayed; however, in the case that the remote control thermistor is effective,
detected temperature by the remote controller thermistor is displayed.

⑵

Press

ON/OFF button.

End.

[In the case that the remote thermistor is ineffective and plural indoor units are connected to one
remote controller ]

⑴

Press AIR CON NO. button for over 5 seconds.

indoor unit No. indicator: “U 000” (blinking)
(Among the connected indoor units, the lowest
number is displayed.)

⑵

Press TEMP

△

or TEMP

▽

button.

Select the indoor unit No.

⑶

Press

MODE button.

Dectder the indoor unit No.
(Example) indoor unit No. indicator: “U 000”
“88” blinks on the temperature setting indicator. (blinking for approximately 2 to 10 seconds while
data is read) Then, the return air temperature is displayed. When AIR CON NO. is pressed, return

to the indoor unit selection display (example, “U 000”).

⑷

Press

ON/OFF button.

End.

PJZ012D069

Screw

⑴

Lower case

Wall

surface

⑷

X Y

⑸

⑶

Remote controller cord

Electrical box
Prepare on site

Two M4 screws (head: ø8 or less) (prepare on site)

⑷

Screw

⑴

Sheath

Peeling length

Remote controller line (nonpolarity)

○

Ｘ ○

Ｙ

Remote controller “Master”

SW1-1 “OFF”

indoor unit

○

Ｘ ○

Ｙ

○

Ｘ ○

Ｙ

Switch

Setting

Function detail

Slave remote controller

Master remote controller

SW1-1

OFF

Remote controller “Slave”

SW1-1 “ON”

Software number

(The number in the left is one
example. Another number
may be shown.)

Wiring outlet

Lower case

⑵

Upper case

⑵

Upper case

⑶

Thin part

SW1

SW1-1:ON (Slave remote controller)

SW1-1:OFF(Master remote controller)

OFF

2 3 4 5 6 7 8 9 0

Function setting

Each function of the remote controller and the indoor unit is automatically set to the initial setting, which is the standard use, on the occasion of connecting the remote controller with the indoor unit. In the case of the standard
use, the setting change is unnecessary. However, if you whould like to change the initial setting “

○

”, change the setting for only the item of the function number.

Record the setting contents and stored them.

⑴

Function setting item by switch on PCB

Switch No.

Setting

Setting detail

Initial setting

SW1-1

Slave remote controller

OFF

Master remote controller

○

SW1-2

Remote controller thermistor enabled

OFF

Remote controller thermistor disabled

○

SW1-3

“MODE” button prohibited

OFF

“MODE” button enabled

○

SW1-4

“ON/OFF” button prohibited

OFF

“ON/OFF” button enabled

○

⑵

Function setting item by button operation

Note 1: The symbol “

※

” in the initial setting varies depending upon the indoor unit and the outdoor unit to be connected, and this is

automatically determined as follows:

Swith No.

Function No.

Function

Setting

Product model

SW1-6

“FAN SPEED”

button

“FAN SPEED” button prohibited Product model whose indoor fan speed is only one step

“FAN SPEED” button enabled Product model whose indoor fan speed is two steps or three

steps

Remote controller function 01

Indoor unit fan
speed

Fan speed: three steps

Product model whose indoor unit fan speed is three steps

Fan speed: two steps (Hi-Lo) Product model whose indoor unit fan speed is two steps
Fan speed: two steps (Hi-Me)
Fan: one step

Product model whose indoor unit fan speed is only one step

Remote controller function 06 “Auto” operation

setting

“Auto” operation enabled

Product model where “Auto” mode is selectable

“Auto” operation disabled

Product model without “Auto” mode

Indoor unit function 13

Heating fan

control

Low fan speed

Product model except FDUS

Intermittent operation

FDUS

Classification

Function No.

Function

Setting No.

Setting

Initial setting

Remarks

Remote

controller

function

Indoor unit fan speed

Fan speed: three steps

※

Note 1 The fan speed is three steps,

Fan speed: two steps (Hi-Lo)

※

Note 1 The fan speed is two steps,

Fan speed: two steps (Hi-Me)

The fan speed is two steps,

Fan: one step

※

Note 1 The fan speed is fixed to one step.

Remote controller
thermistor at the time
of cooling

Remote controller thermistor: no offset

○

Remote controller thermistor: +3.0 °C

At the time of cooling, in the case of remote controller thermistor enabled, offset temperature at +3.0°C.

Remote controller thermistor: +2.0 °C

At the time of cooling, in the case of remote controller thermistor enabled, offset temperature at +2.0°C.

Remote controller thermistor: +1.0 °C

At the time of cooling, in the case of remote controller thermistor enabled, offset temperature at +1.0°C.

Remote controller thermistor: -1.0 °C

At the time of cooling, in the case of remote controller thermistor enabled, offset temperature at -1.0°C.

Remote controller thermistor: -2.0 °C

At the time of cooling, in the case of remote controller thermistor enabled, offset temperature at -2.0°C.

Remote controller thermistor: -3.0 °C

At the time of cooling, in the case of remote controller thermistor enabled, offsett temperature at -3.0°C.

Remote controller
thermistor at the time
of heating

Remote controller thermistor: no offset

○

Remote controller thermistor: +3.0 °C

At the time of heating, in the case of remote controller thermistor enabled, offset temperature at +3.0°C.

Remote controller thermistor: +2.0 °C

At the time of heating, in the case of remote controller thermistor enabled, offset temperature at +2.0°C.

Remote controller thermistor: +1.0 °C

At the time of heating, in the case of remote controller thermistor enabled, offset temperature at +1.0°C.

Remote controller thermistor: -1.0 °C

At the time of heating, in the case of remote controller thermistor enabled, offset temperature at -1.0°C.

Remote controller thermistor: -2.0 °C

At the time of heating, in the case of remote controller thermistor enabled, offset temperature at -2.0°C.

Remote controller thermistor: -3.0 °C

At the time of heating, in the case of remote controller thermistor enabled, offset temperature at -3.0°C.

Ventilation setting

No ventilator connection

○

Ventilator links air-conditioner

In case of Single split series, by connecting ventilation device to CNT of the indoor printed circuit board (in case of VRF series, by

connecting it to CND of the indoor printed circuit board), the operation of ventilation device is linked with the operation of indoor unit.

“Auto” operation
setting

“Auto” operation enabled

※

Note 1

“Auto” operation disabled

※

Note 1 “Auto” operation disabled

Indoor unit

function

Operation permission/
prohibition

Disabled

○

Enabled

Operation permission/prohibition controller is enabled.

External input

Level input

○

Pulse input

Fan speed setting

Standard

Note2

High speed 1

Note2

High speed 2

Note2

Fan remaining
operation at the time
of cooling

No remaining operation

○

After cooling stopped, no fan remaining operation

0.5 hours

After cooling stopped, fan remaining operation for 0.5 hours

1 hour

After cooling stopped, fan remaining operation for 1 hour

6 hours

After cooling stopped, fan remaining operation for 6 hours

Fan remaining
operation at the time
of heating

No remaining operation

○

After heating stopped or after heating thermostat OFF, no fan remaining operation

0.5 hours

After heating stopped or after heating thermostat OFF, fan remaining operation for 0.5 hours

2 hours

After heating stopped or after heating thermostat OFF, fan remaining operation for 2 hours

6 hours

After heating stopped or after heating thermostat OFF, fan remaining operation for 6 hours

Setting temperature
offset at the time of
heating

No offset

○

Setting temperature 3.0 °C

The setting temperature at the time of heating is offset by +3.0 °C.

Setting temperature 2.0 °C

The setting temperature at the time of heating is offset by +2.0 °C.

Setting temperature 1.0 °C

The setting temperature at the time of heating is offset by +1.0 °C.

Heating fan controller

Low fan speed

※

Note 1 At the time of heating thermostat OFF, operate with low fan speed.

Setting fan speed

At the time of heating thermostat OFF, operate with the setting fan speed.

Intermittent operation

※

Note 1 At the time of heatingr thermostat OFF, intermittently operate.

Fan off

At the time of heating thermostat OFF, a fan will be stopped.

When the remote controller thermistor is enabled, automatically set to “Fan off”. Do not set at the time of the indoor unit thermistor.

Return air temperature
offset

No offset

○

Return air temperature 2.0 °C

Offset the return air temperature of the indoor unit by +2.0 °C.

Return air temperature 1.5 °C

Offset the return air temperature of the indoor unit by +1.5 °C.

Return air temperature 1.0 °C

Offset the return air temperature of the indoor unit by +1.0 °C.

Return air temperature offset -1.0 °C

Offset the return air temperature of the indoor unit by -1.0 °C.

Return air temperature offset -1.5 °C

Offset the return air temperature of the indoor unit by -1.5 °C.

Return air temperature offset -2.0 °C

Offset the return air temperature of the indoor unit by -2.0 °C.

[In the case of selecting the indoor unit function (07-14)]

①

“88” blinks on the temperature setting indicators.

(blinking for approximately 2 to 10 seconds while data is read)

↓

After that, the current setting number of the selected function number blinks.

(Example)

Function number: “07” (lighting)
Setting number: “01” (blinking)

Proceed to

②

[Note]
a.

In the case of connecting one remote control to plural indoor units, the display
will be as follows:

Indoor unit No. display: “U 000” (blinking)

(Display the lowest number among the connected indoor units.)

Press TEMP

△

or TEMP

▽

button.

Select the indoor unit No. to be set.
If “U ALL” is selected, the same setting can be set to all units.

Press

MODE button.

Decide the indoor unit No.
“88” blinks on the temperature setting indicators. (blinking for 2 to 10 seconds while data
is read)
When AIR CON NO. button is pressed, go back to the indoor unit selection display (for
example, “U 000” blinking).

②

Press TEMP

△

or TEMP

▽

button.

Select the setting number

③

Press

MODE button.

The setting is completed.
Light is on for approximately 3 to 20 seconds while data of the decided function No. and
setting No. is transmitted.
(Example)

Indoor unit No.: “U 000” (lighting for 3 to 20 seconds)
Function number: “07” (lighting for 3 to 20 seconds)
Setting number: “01” (lighting for 3 to 20 seconds)

Then, the screen goes back to the function number blinking indication

⑴

, if the setting

is sequentially conducted, continue with the same procedures. If the setting is finished,
proceed to

⑸

⑴

Stop air-conditioning, and simultaneously press AIR CON NO. and

MODE buttons

at the same time for over three seconds.

The function number “01” blinks in the upper right.

⑵

Press TEMP

△

or TEMP

▽

button.

Select the function number.

⑶

Press

MODE button.

Decide the function number.

⑷

[In the case of selecting the remote controller function (01-06)]

①

The current setting number of the selected function number blinks

(Example)

Function number: “01” (lighting)

Setting number: “01” (blinking)

②

Press TEMP

△

or TEMP

▽

button.

Select the setting number.

③

Press

MODE button.

The setting is completed.

Light is on for approximately 3 to 20 seconds while data of the
decided function No. and setting No. is transmitted.

(Example)

Function number: “01” (lighting for 3 to 20 seconds)

Setting number: “01” (lighting for 3 to 20 seconds)

Then, the screen goes back to the function number blinking
indication

⑴

, if the setting is sequentially conducted, continue

with the same procedures. If the setting is finished, proceed to

⑸

Press

ON/OFF button.

The setting is completed.

Function number

Setting number

Function number

Setting number

Function number

Setting number

Function number

Indoor unit No.

(In the case of

connecting

plural indoor

units)

Function number

Setting number

SW1

OFF

2 3 4 5 6 7 8 9 0

• As for the slave remote controller, function setting is impossible

other than SW1-1.

•

In the indoor unit with only one fan speed, “FAN SPEED” button cannot
be enabled.

・

Even if

ON/OFF button is pressed during setting, the setting is ended. However, any details where the setting has not been completed will be ineffective.

・

The setting contents are stored in the controller, and even if the power failure

occur, this will not be lost.

[Confirmation method for current setting]

According to the operation, the “setting number” displayed first after selecting “function number” and pressing

MODE button is the currently set content.

(However, in the case of selecting “U ALL” (all units), the setting number of the lowest number among the indoor units is displayed.)

Decide button

Start button

Select button

End button

Note 3: As for plural indoor unit, set indoor functions to each master and slave indoor unit.

But only master indoor unit is received the setting change of indoor unit function “07 Operation permission/
prohibition” and “08 External input”.

Note 2: Fan speed of “High speed” setting

Fan speed setting

Indoor unit fan speed setting

Standard

−

Mid

−

Mid

High speed 1

・

UHi

−

Mid

UHi

−

Mid

UHi

−

Initial setting of some indoor unit is “High speed”.

How to set functions by button operation

Switch No.

Setting

Setting detail

Initial setting

SW1-5

“TEMP” button prohibited

OFF

“TEMP” button enabled

○

SW1-6

“FAN SPEED” button prohibited

※

Note 1

OFF

“FAN SPEED” button enabled

※

Note 1

SW1-7

Auto restart function enabled

OFF

Auto restart function disabled

○

SW1-8, 9, 0

Not used

OFF

PJZ012D069.indd 1

2008/11/13 11:42:01

Summary of Contents for FDF100VNVD




















































































































































































































Search results

Summary of Contents for FDF100VNVD

Reviews:

Related manuals for FDF100VNVD

Brands by name

Popular brands

Mitsubishi Electric FDF100VNVD, Technical Manual

Search results

Summary of Contents for FDF100VNVD

Reviews:

Related manuals for FDF100VNVD

Brands by name

Popular brands