Mitsubishi Electric FDF100VNVD Technical Manual Download Page 158

Page: 158 / 211

157

INSPECT I/U

(When 1 or 2 remote controllers are connected)

Keeps flashing

Stays OFF

Keeps flashing 2 times flash

1. Applicable model

5. Troubleshooting

All models

Diagnosis

Countermeasure

Are 2 units

of remote controller

connected?

Is it set

at the slave remote

controller?

⑴，

⑵

Note (1) Use SW1 to set at

master or slave.

Note (2)

“Slave” is displayed

on the remote

controller LCD.

⑵

Does it

become normal?

Do more than

one indoor units have the

same address?

Are remote

controller wires laid

along high voltage

wires?

Does DM

start 60 seconds later

automatically.

Disconnect the connecting

wire

�

between the indoor

and outdoor unit.

Power supply reset

YES

Set one remote controller

for “Master” and the other

for “Slave”

Set SW1 on remote

controller PCB at “Master”.

Set address again. (SW2 on

indoor control PCB)

Separate remote controller

wires from high voltage

wires.

Defective indoor control

PCB

➞

Replace.

Defective remote controller

➞

Change.

2. Error detection method

Communication between indoor

unit and remote controller

is disabled for more than 30

minutes after the power on.

3. Condition of Error displayed

Same as above

4. Presumable cause

• Improper setting

• Surrounding environment

• Defective remote controller

communication circuit

• Faulty indoor control PCB

Note:

If any error is detected 30 minutes after displaying “

WAIT

” on the remote controller, the display changes to

“INSPECT I/U”.

Error code

Remote controller:

LED

Green

Red

Indoor

Outdoor

Content

'11 • PAC-T-160

Summary of Contents for FDF100VNVD




















































































































































































































Search results

Summary of Contents for FDF100VNVD

Reviews:

Related manuals for FDF100VNVD

Brands by name

Popular brands

Mitsubishi Electric FDF100VNVD, Technical Manual

Search results

Summary of Contents for FDF100VNVD

Reviews:

Related manuals for FDF100VNVD

Brands by name

Popular brands