75
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Operations
LAN B (Communication) Setting
This item is used to make the communication settings between
this unit and the PC connected via LAN B.
System Menu
COM/LAN
1
LAN B (Communication) Setting
Alarm Notification Detailed Infomation
D
3
LAN B Address Setting
1
Service Port Setting
2
E-mail Notification Information
3
IP Alarm Notification Information
4
step
2
step
7
step
1
step
3
step
5
step
6
E-mail Notification Detailed Infomation
D
step
4
(LAN B Address Setting)
step
1.
Set the IP address, sub net mask, and Gateway.
• MAC address is shown on the bottom of the
screen of <LAN B (Communication) Setting>.
• Do not assign the same IP address or network address
for LAN A and LAN B.
• Do not assign “000.000.000.000” to IP address and
broadcast address. If this address is assigned,
communications or any other functions of this unit may
not be performed correctly.
• The setting cannot be changed during recording. Stop
recording before changing the setting.
(Service Port Setting)
step
2.
Set the port setting of “Web,” “User Access,” and
“Administrator.”
• This item is used to set the port number which is
necessary to connect a PC.
• Normally, leave the setting as is.
• Do not change the setting without sufficient knowledge
about the network setting.
• When making the settings other than the port settings
of “Web,” “User Access,” and “Administrator,” using
the specified application is required. Consult your
dealer about the specified application.
(E-mail Notification Information)
step
3.
Check the settings of “E-Mail Address” and
“Recorder ID.”
• When selecting “Mail,” the e-mail is sent for the
selected address.
• Using the web function of this unit is required to input
“E-Mail Address” and “Recorder ID.”
(E-mail Notification Detailed Information)
step
4.
Check the contents to be transmitted to the PC.
Remain:
Transmits signal when the remaining
capacity reaches the value set for Call out setting.
Temp/Fan:
Transmits signal when the high
temperature is detected or the fan is stopped.
Reboot:
Transmits signal when the unit is rebooted.
Record:
Transmits signal when the recording is
started.
Alarm:
Transmits signal when the alarm recording
is started.
Sensor:
Transmits signal when the signal is input
to the terminal on the rear panel.
• Using the web function of this unit is required to
change the contents to be transmitted.
(IP Alarm Notification Information)
step
5.
Check the settings of “IP Address” and “Target Port.”
• This item is used to transmit warning signals or
signals of status change such as a closure of a
rear terminal to the PC connected.
• When selecting “Test,” the sending test for the
set IP address and port is executed.
• Using the specified application is required to change
the IP address and target port. Consult your dealer
about the specified application.
• Transmission of signal to broadcast address is not
supported.
(Alarm Notification Detailed Information)
step
6.
Check the contents to be transmitted to the PC.
Remain:
Transmits signal when the remaining
capacity reaches the value set for Call out setting.
Temp/Fan:
Transmits signal when the high
temperature is detected or the fan is stopped.
Reboot:
Transmits signal when the unit is rebooted.
Record:
Transmits signal when the recording is
started.
Alarm:
Transmits signal when the alarm recording
is started.
Sensor:
Transmits signal when the signal is input
to the terminal on the rear panel.
• Using the specified application is required to change
the contents to be transmitted. Consult your dealer
about the specified application.
step
7.
Select “Return” in the screen of <LAN B
(Communication) Setting>.
• When the setting of “IP Address,” “Sub Net Mask,”
“Gateway,” or “Service Port Setting” is changed,
the power turns off automatically and then the
unit restarts.
Summary of Contents for 16CH DIGITAL RECORDER DX-TL5000U
Page 143: ...872C355B2 PRINTED IN MALAYSIA ...
