6 Operation for Functions
6-20
Outline of the machine setup functions
Feeding / TakeUP
For heavy-duty feeding / take-up device, set whether to use or not to use.
Available setting values: [ON, OFF]
Aftter switching ON to OFF, move the tension-bar of each device to the lock position.
Especially for heavy-duty take-up device, you cannot switch the setting unless moving the bar to the lock position.
DRYNESS FEED
Set whether or not to perform feeding for media drying.
Available setting values: [ON, OFF]
With DRYNESS FEED set to ON, the printer feeds the media up to the location of the post-heater where
the media is dried.
After waiting for a period of time that has been set by the setup Function (DRYING TIME - DRAWend),
the printer performs the next printing (media cutting). No back feed is performed. (Printing will be started
at the position to which the media has been fed for media drying.)
CONFIRM. FEED
Set whether or not to perform feeding the media after test printing for checking of the printing result.
Available setting values: [ON , OFF]
With CONFIRM. FEED set to ON, the media after completion of printing will be fed up to a position
where the print result can be checked on the platen.
In addition, when CONFIRM. FEED has been set to ON, [BACK FEED] can be set to ON using the
[FUNCTION] key.
The [BACK FEED] function returns to the original position the media that has been fed by the [CON-
FIRM. FEED] function.
Available setting values: [ON , OFF]
PRE-FEED METHOD
Switch the operation method of pre-feeding.
Available setting values: [FORE (***mm), FORE&BACK]
When FORE (***mm) is set, a media is pre-feeded at specified amout, to remove the media that has waved
by the heat of the heater.
Change the feeding length of the media with [FUNCTION] key when FORE is selected.
Available setting values: [10 to 1000mm]
When FORE&BACK is set, a media is pre-feeded back and forth at specific amout, to avoid media sticking.
HEATER SETUP
Set the temperature that determines whether the post-heater is reached to the specified temperature.
Available setting values: [STD, set -5°C, set -10°C, set -15°C, set -20°C]
When STD is set, this machine assumes the post-heater temperature has been reached when it reaches to
the specified temperature.
When Set -5°C, Set -10°C, Set -15°C, or Set -20°C is set, this machine assumes the post-heater tempera-
ture has been reached when the temperature is more than the set one subtracted the selected one.
Post-heater temperature easily lowers after printing.
In case of printing some data continuously with STD is set, if the temperature does not reach between com-
pletion of one data printing and a start of next printing, it displays “Temperature controlling.” It does not
start printing until the temperature reaches.
If you want to print continuously at low temperature, select other than STD.
Summary of Contents for JV5-320S
