MIMAKI JV5-320S, Operation Manual

Page: 231 / 312

5-23
Troubles for which error messages are displayed
∗∗∗∗
ERROR 116
∗∗∗∗
NCU I/F 00
An error occurred in the control sys-
tem. Operation can be resumed after turning
off the nozzle missing detection func-
tion.
Turn off the power to the printer and
turn it on after a while.
If the error occurs frequently, contact
your local distributor to call for ser-
vice.
∗∗∗∗
ERROR 116
∗∗∗∗
NCU I/F 01
An error occurred in the control sys-
tem.
∗∗∗∗
ERROR 120
∗∗∗∗
ENVIRONMENT TEMP(LO)
The ambient temperature is outside the
permissible temperature range (too
low). Adjust the ambient temperature within
a range of available temperature.
∗∗∗∗ ERROR 121 ∗∗∗∗
ENVIRONMENT TEMP(HI)
The ambient temperature is outside the
permissible temperature range (too
high).
∗∗∗∗
ERROR 122
∗∗∗∗
ENV.TEMP.LO:DewDrops
As the ambient temperature is low,
head condensation may occur. Raise the ambient temperature.
(To use without changing the setting,
press the [ENTER] key.)
∗∗∗∗
ERROR 134
∗∗∗∗
MEDIA ENCODER:SENSOR
An error occurred in detection by the
media encoder.
(Counting impossible) Select “NORMAL” in [MediaFeed
SETUP] - [FEED METHOD] or turn
off the power to the printer and turn it
on after a while.
If the same error message appears
again, contact your local distributor to
call for service.
∗∗∗∗
ERROR 134
∗∗∗∗
MEDIA ENCODER:DIR.
An error occurred in detection by the
media encoder.
(Wrong orientation)
∗∗∗∗
ERROR 134
∗∗∗∗
MEDIA ENCODER:ORIGIN
An error occurred in detection by the
media encoder.
(Origin detection impossible)
∗∗∗∗
ERROR 135
∗∗∗∗
MEDIA FEED UNUSUAL
An error occurred in media feed. Check that the media has been set
properly, and the media still remains.
Using [SET UP] - [MediaFeed
SETUP] - [MOVEMENT TEST], per-
form testing to see if the media is com-
patible with direct feed.
If the error status is not cleared even
with a proper media, select “NOR-
MAL” in [SET UP] - [MediaFeed
SETUP] - [FEED METHOD] or turn
off the power to the printer and turn it
on after a while.
If the same error message appears
again, contact your local distributor to
call for service.
∗∗∗∗
ERROR 142
∗∗∗∗
INK LEAK
Ink leakage was detected. Turn off the power to the printer and
turn it on after a while.
If the same error message appears
again, contact your local distributor to
call for service.
∗∗∗∗
ERROR 143
∗∗∗∗
CARTRIDGE SOLENOID
An error occurred in the control sys-
tem.
∗∗∗∗
ERROR 143
∗∗∗∗
WASH CART. SOLENOID
An error occurred in the control sys-
tem.
∗∗∗∗
ERROR 144
∗∗∗∗
CARTRIDGE SET !
An error occurred in the control sys-
tem. Set a cartridge.
∗∗∗∗
ERROR 145
∗∗∗∗
FlushingBOX EXCHANGE
Time for replacing the flushing box has
passed. Make a call for services.
Error message Cause Remedy