Michell Instruments XZR-400-BM User Manual Download

Page: 71 / 102

XZR400 Series User’s Manual

Michell Instruments

CALIBRATION

Managing The Alarms During The Calibration Sequence

The alarms can be active or inactive during the calibration sequence.

When

is on in the

Active during ADJ

section on screen page 5-3 the alarm contacts

are not active during the calibration sequence.

When

YES

is on in the

Active during ADJ

section on screen page 5-3 the alarm contacts

will be activated during the calibration sequence and will respond according to the

con

guration set by the user.

De-Activation of Alarms

The alarms may be de-activated during installation and set-up. If the alarms are de-

activated and the system detects a fault and/or an alarm threshold is passed, the alarm

relays are not activated. In this case a message describing the fault will appear at the

bottom of the default screen page 3.

When

is on in the

Inhibit Alarms

section the alarms are operative.

When

YES

is on in the

Inhibit Alarms

section the alarms are de-activated.

Summary of Contents for XZR-400-BM







































































































Search results

Summary of Contents for XZR-400-BM

Reviews:

Related manuals for XZR-400-BM

Brands by name

Popular brands

Michell Instruments XZR-400-BM, User Manual

Search results

Summary of Contents for XZR-400-BM

Reviews:

Related manuals for XZR-400-BM

Brands by name

Popular brands