Michell Instruments XZR-400-BM User Manual Download

Page: 60 / 102

XZR400 Series User’s Manual

97472 Issue 3, August 2018

OPERATION

Misc Tab

The Misc tab of the System screen concerns the oven temperature setpoint, the menu

display language and the access code modi

cation.

•

Touch the + and – area to set

Hour

System

5.5

634ºC

Setpoint

Language

New access code

English

****

Misc

Area

Function

Setpoint

Enter the oven temperature value that the analyzer will use to operate.

The default value is 634°C. An unsuitable temperature setting reduces

the performance of the analyzer and can damage the MSRS oxygen

measuring cell.

Language

Touch the

Language

area. In the opened window, change the

displayed language. The new language will be applied at the next

start.

NOTE: the language selection is proposed if this choice was

not selected at the analyzer start.

New

access

code

Modi

es the expert level code. By default, the expert code is

Warning: If the access code is forgotten the equipment will

need to be returned to the factory for Expert level code reset.

Factory

settings

The analyzer parameter values defaults are set at the factory, namely

•

Oven temperature: 634°C

•

Alarm No. 1 High mode, threshold: 3 ppm

•

Alarm No. 2 High mode, threshold: 3.5 ppm

•

Low scale and high scale, 4-20 mA output No. 1: 0.1 and

10 ppm

•

Low scale and high scale, 4-20 mA output No. 2: 0.1 and

1000 ppm

Summary of Contents for XZR-400-BM







































































































Search results

Summary of Contents for XZR-400-BM

Reviews:

Related manuals for XZR-400-BM

Brands by name

Popular brands

Michell Instruments XZR-400-BM, User Manual

Search results

Summary of Contents for XZR-400-BM

Reviews:

Related manuals for XZR-400-BM

Brands by name

Popular brands