Michell Instruments XZR-400-BM User Manual Download

Page: 16 / 102

XZR400 Series User’s Manual

97472 Issue 3, August 2018

INSTALLATION

2 INSTALLATION

It is essential that the installation of the electrical and gas

supplies to this analyzer be undertaken by qualifi ed personnel.

2.1

Unpacking the Analyzer

Open the box and unpack carefully as follows. Save all the packing materials for the

purpose of returning the instrument for any warranty claims.

Remove the accessories (if ordered with the analyzer). If no accessories

have been ordered the box should contain the following items:

•

XZR400 Series Oxygen Analyzer

•

Power cable (except XZR400A2 model)

• User’s

Manual

•

Test result sheet

Remove the documentation and packing material.

Remove the analyzer and power cable.

2.2 Preparation

Carefully read the following guidelines before installing the analyzer. If you are not sure

about the installation conditions and other important factors please contact a Michell

Instruments’ Application Engineer or a Michell Instruments’ representative prior to the

installation.

The following list will help you to identify the recommended preparation steps:

•

The analyzer should be installed at ambient temperatures between 0 and

+55°C (32 to +131°F).

•

The location of the installation should allow access to the display.

•

The location of the installation should not expose the analyzer to any

vibration.

•

The cables should not be exposed to extreme temperatures and mechanical

strain.

Summary of Contents for XZR-400-BM







































































































Search results

Summary of Contents for XZR-400-BM

Reviews:

Related manuals for XZR-400-BM

Brands by name

Popular brands

Michell Instruments XZR-400-BM, User Manual

Search results

Summary of Contents for XZR-400-BM

Reviews:

Related manuals for XZR-400-BM

Brands by name

Popular brands