Michell Instruments XZR-400-BM User Manual Download Page 56

Page: 56 / 102

XZR400 Series User’s Manual

97472 Issue 3, August 2018

OPERATION

Main Tab

Main

Level

Auto adjustment

5.4.1

External trigger

T0 adj

Adjustment period

Unit

12:00

1 d

Process

Enable

Start

Process

Area

Function

Enable/Disable

Enables/disables the launch of the automatic adjustment.

Start

Management of the start of the auto-adjust procedure.

•

Start

: the auto adjust sequence is launched immediately,

regardless of the other settings.

•

T0 start

: the auto-adjust sequence is launched at the time

speci

ed by the area

T0 Adjust.

The interval is set by

Adjustment period

(see below).

External trigger

Management of an external launch control button (push-button or

dry contact from an external PLC) controlling the launch of the auto

adjust sequence (as opposed to the automatic launch of the Inter

Start and Inter Adjust commands).

•

: pressing the external button connected to terminals

5-6 of the D-Sub DA15 connector or the 8 pluggable

pin connector will not allow the launch of the auto adjust

sequence.

•

Yes

: pressing the external button connected to terminals

5-6 of the D-Sub DA15 connector or the 8 pluggable pin

connector will allow the launch of the auto adjust sequence.

T0 adj

Sets the start time of the next auto-adjust.

Adjustment

period

Adjustment interval

Sets the time interval in hours or days between two auto-adjust

sequences. See below.

Unit

d (day) or hr (hour)

nes the time unit of the Adjustment interval.

Inter adjust:

Intervals in hours or days

between automatic

adjustments

Automatic

adjustment

sequence

Automatic

adjustment

sequence

next start

time

Summary of Contents for XZR-400-BM







































































































Search results

Summary of Contents for XZR-400-BM

Reviews:

Brands by name

Popular brands

Michell Instruments XZR-400-BM, User Manual

Search results

Summary of Contents for XZR-400-BM

Reviews:

Brands by name

Popular brands