manualshive.com logo in svg

Michell Instruments XZR-400-BM, User Manual

Share
Download
Michell Instruments XZR-400-BM User Manual Download Page 54

XZR400 Series User’s Manual

44

 

 

 

97472 Issue 3, August 2018

OPERATION

The Alarm 1 or Alarm 2 Tab

This screen is used to set the alarm function mode (high, low), the threshold and 

hysteresis for the selected alarm 1 or 2.  

It is used mainly to enable or disable the alarms during the adjustment phases and 

during normal analyzer operation.  

• 

Touch the area to select it and change it. 

• 

Enter any new numeric value on the virtual keypad. 

• Click 

OK

 to con

fi

 rm or 

Cancel

 to discard the changes. 

Main

Alarms

5.3

Low

Type

Threshold

Unit

Hysteresis

1.0%

%

0.1%

Alarm 2

Alarm 1

Figure 39 

Alarm Screen (Alarm 1)

Area

Function

Type

Sets the behaviour for alarm (1 or 2 according to the highlighted tab).
• 

Low

: the alarm will be activated when the measurement value 

is equal or below the threshold set for the Alarm threshold 

line. The alarm must be disabled when the measurement 

value is above the threshold set for the Alarm threshold line.

• 

High

: the alarm will be activated when the measurement value 

is equal to or above the threshold set for the Alarm threshold 

line. The alarm must be disabled when the measurement 

value is below the threshold set for the Alarm threshold line. 

Threshold

Con

fi

 gures the alarm threshold value. Select the value and unit in relation 

to the future measurement. 

Hysteresis 

Sets the alarm 'delay' value to return to alarm-off condition. The greater 

this value is, the more the return to alarm-off condition value must be 

delayed. For example, with a hysteresis of 3ppm over a 15ppm alarm 

value, the alarm is triggered at 15ppm, but returns to the alarm-off 

position at a 12ppm value (15ppm - 3ppm).
Returns to the Main Menu Screen. 

Summary of Contents for XZR-400-BM







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands