Michell Instruments XZR-400-BM Page 47 User Manual Download

Page: 47 / 102

XZR400 Series User’s Manual

Michell Instruments

OPERATION

3.5

Control Parameters Display

On the Measurement Display Screen (3) touch the

VIEW

area

The Control Parameters Screen (3.1) will appear.

Adjustment

Maintenance

3.1

634.0ºC
30.7ºC
-122.76 mV
1036 mBar
2.5 L/h
0.00

Oven

Room temp

Sensor Voltage

Atm pressure

Flow

Control parameters

O2 27.35 ppm

Figure 33

Control Parameters Screen

This displays the following information about the analyzer.

Oven

Current temperature of the hot joint of the thermocouple

corresponding to oven temperature. This must be 634°C.

Temperatures 30°C below the reference and 50°C above the

reference trigger a general alarm.

Room Temperature

Measure taken on the motherboard. This measurement is only

used to compensate for the cold solder joint of the thermocouple.

Sensor Voltage

Measurement in mV of the voltage supplied by the measuring

cell, which must be between -300 and +250 mV. A value greater

than the upper limit generates a MSRS fault alarm.

Atm pressure

The pressure at the analyzer outlet must be near atmospheric

pressure (between 800 and 1750 mbar). A value above 1200

mbar and under 800 mbar generates an oxygen measurement

error.

NOTE: If the pressure is greater than 1750 mbar,

the atmospheric pressure sensor can be damaged

irreversibly.

Flow

The sample's

ow in l/hour must be 2 ±1 l/h. A

ow value

below 0.5 or greater than 3.5 l/h generates a general fault alarm

displaying a Flow fault.

Measured oxygen percentage
Return to Main Screen 3. The display returns to the Main Screen

automatically if the touch screen is not used for 2 minutes.

Adjust

Displays the adjustment screen to calibrate the analyzer.

Maintenance

Displays the analyzer's parameter setting screen (access code,

outputs, alarm limits, time-stamp, RS485,

ow corrections).

Summary of Contents for XZR-400-BM







































































































Search results

Summary of Contents for XZR-400-BM

Reviews:

Related manuals for XZR-400-BM

Brands by name

Popular brands

Michell Instruments XZR-400-BM, User Manual

Search results

Summary of Contents for XZR-400-BM

Reviews:

Related manuals for XZR-400-BM

Brands by name

Popular brands