Michell Instruments XZR-400-BM User Manual Download

Page: 53 / 102

XZR400 Series User’s Manual

Michell Instruments

OPERATION

3.6.2 Alarms

The Main Tab

The Alarms Screen sets the general behaviour for alarms 1 and 2.

•

Touch the area to select it and change it.

• Click

to con

rm or

Cancel

to discard the changes.

Alarm 1

Alarms

5.3

Enable when adj

Disabled

Alarm 2

Main

Figure 38

Alarm Screen (Main)

Area

Function

Enable when adj

Sets the behaviour for alarms 1 and 2 exclusively during auto adjust

operations or manual.
•

: exceeding the alarm threshold will not trigger the

relay for alarms 1 and 2 during adjustment operations, or

when alarm set off is con

gured by the user.

•

Yes

: exceeding the alarm threshold will trigger the relay

for alarms 1 and 2 during adjustment operations, or when

alarm set off is con

gured by the user.

Disabled

Sets the current behaviour for alarms 1 and 2 and that of the General

fault exclusively in normal mode of operation (excluding adjustment).
•

: the alarms are operational; the corresponding alarm

will be activated when an alarm is triggered and/or a fault

occurs. This is the standard choice for the analyzer in

normal operation.

•

Yes

: no alarms will be activated regardless of the alarm and/

or fault present. Use this option during the commissioning

of the analyzer, especially before the wiring the alarms.
The blinking

Alarms Disabled

message will be displayed

on the Measurement Display Screen (3).

NOTE: Operating with alarms disabled must only be done

temporarily, particularly during adjustments.

Alarm 1 tab

Touch the area to display the alarm 1 threshold change screen.

Alarm 2 tab

Touch the area to display the alarm 2 threshold change screen.
Returns to the Main Menu Screen.

Summary of Contents for XZR-400-BM







































































































Search results

Summary of Contents for XZR-400-BM

Reviews:

Related manuals for XZR-400-BM

Brands by name

Popular brands

Michell Instruments XZR-400-BM, User Manual

Search results

Summary of Contents for XZR-400-BM

Reviews:

Related manuals for XZR-400-BM

Brands by name

Popular brands