Metronix ARS 2320 Product Manual Download Page 36

Page: 36 / 171

Product description

Page 36

Product Manual „Servo drives ARS 2320, ARS 2340, ARS 2320W, ARS 2360W“

Version 8.0

3.4

Communication interfaces

The servo drive ARS 2300 has several communication interfaces. The basic device itself is already
equipped with many of these interfaces.

The following communication interfaces are included in the basic device:



Serial interface [X5]: RS232/RS485



Fieldbus system [X4]: CANopen



I/O interface [X1]: Digital and analogue In- and outputs

The serial interface is particularly important for the connection of a PC and for the use of the Metronix
ServoCommander™ parameterisation tool.

The fieldbus systems PROFIBUS-DP, sercos and EtherCAT are extension options that can be
implemented in the form of plug-in modules. If required, customer-specific fieldbus protocols can also
be realised.

In any case, the servo drive of this design always works as a slave to the fieldbus.

3.4.1

Serial interface [X5]

The RS232 protocol is mainly intended to be a parameterisation interface, but also allows the control
of the servo drive.

3.4.2

CAN interface [X4]

The CANopen protocol as per DS301 with application profile DSP402 is implemented.

The specific Metronix CAN protocol of the previous ARS devices is no longer supported
by the ARS 2300 series.

Summary of Contents for ARS 2320












































































































































































Search results

Summary of Contents for ARS 2320

Reviews:

Related manuals for ARS 2320

Brands by name

Popular brands

Metronix ARS 2320, Product Manual

Search results

Summary of Contents for ARS 2320

Reviews:

Related manuals for ARS 2320

Brands by name

Popular brands