manualshive.com logo in svg

Mercedes-Benz B 250 e 2015, Owner'S Manual

The Mercedes-Benz B 250 e 2015 is a sleek and eco-friendly electric vehicle, perfect for the environmentally conscious driver. To fully understand the features and operation of this cutting-edge car, make sure to download the Owner's Manual from manualshive.com for free. Experience the thrill of owning this innovative vehicle today.

Share
Download
background image

X

Take ratchet ring spanner

?

out of the vehi-

cle tool kit and place it on the hexagon nut of

jack

=

so that the letters AUF are visible.

X

Position jack

=

at jacking point

;

.

X

Make sure that the base of the jack is posi-

tioned vertically under the jacking point.

X

Turn ratchet ring spanner

?

until jack

=

sits

completely on jacking point

;

and the base

of the jack lies evenly on the ground.

X

Turn ratchet ring spanner

?

until the tyre is

raised a maximum of 3 cm from the ground.

Removing a wheel

!

Do not place wheel bolts in sand or dirt. The

threads of the wheel bolts and wheel hubs

could otherwise be damaged when the bolts

are tightened.

X

Unscrew the wheel bolts.

X

Remove the wheel.

Fitting a new wheel

G

WARNING

Oiled or greased wheel bolts or damaged

wheel bolts/hub threads can cause the wheel

bolts to come loose. As a result, you could

lose a wheel while driving. There is a risk of

accident.
Never oil or grease wheel bolts. In the event of

damage to the threads, contact a qualified

specialist workshop immediately. Have the

damaged wheel bolts or hub threads

replaced/renewed. Do not continue driving.

G

WARNING

If you tighten the wheel bolts or wheel nuts

when the vehicle is raised, the jack could tip

over. There is a risk of injury.
Only tighten the wheel bolts or wheel nuts

when the vehicle is on the ground.

Observe the instructions and safety notes on

"Changing a wheel" (

Y

page 273).

Only use wheel bolts that have been designed

for the wheel and the vehicle. For safety rea-

sons, Mercedes-Benz recommends that you

only use wheel bolts which have been approved

for Mercedes-Benz vehicles and the respective

wheel.

X

Clean the wheel and wheel hub contact sur-

faces.

X

Place the new wheel on the wheel hub and

push it on.

X

Tighten the wheel bolts until they are finger-

tight.

Lowering the vehicle

G

WARNING

The wheels could work loose if the wheel nuts

and bolts are not tightened to the specified

tightening torque. There is a risk of accident.

276

Changing a wheel

Wheels

and

tyres

Summary of Contents for B 250 e 2015






































































































































































































































































































Reviews:

No comments

Related manuals for B 250 e 2015

Samsung HF1000 User Manual preview
HF1000
Brand: Samsung Pages: 133
Eaton Green Motion Building Quick Start Manual preview
Green Motion Building
Brand: Eaton Pages: 12
GARO TWIN+ Assembly Instructions / End User Instruction preview
TWIN+
Brand: GARO Pages: 23
GARO LS4 Wallmounted Operational Instructions preview
LS4 Wallmounted
Brand: GARO Pages: 15
LAMBORGHINI URUS Quick Manual preview
URUS
Brand: LAMBORGHINI Pages: 48
JANE be cool boosty Manual preview
be cool boosty
Brand: JANE Pages: 21
Axxess AX-DSPX-HYKIA2 Installation Instructions preview
AX-DSPX-HYKIA2
Brand: Axxess Pages: 4
Vintage Air 473275 Manual preview
473275
Brand: Vintage Air Pages: 14
Yakima RoadShower 10G Quick Start Manual preview
RoadShower 10G
Brand: Yakima Pages: 12
Ford 2004 Navigator Owner'S Manual preview
2004 Navigator
Brand: Ford Pages: 368
TATA Motors 2013 Nano Owner'S Manual preview
2013 Nano
Brand: TATA Motors Pages: 136
CTEK D250S Dual Manual preview
D250S Dual
Brand: CTEK Pages: 84
Fisher Body FOLDING TOP 1971 Service Manual preview
FOLDING TOP 1971
Brand: Fisher Body Pages: 37
Manik 519952T Installation Instructions preview
519952T
Brand: Manik Pages: 2
Mercedes-Benz Sprinter 2003 Manual preview
Sprinter 2003
Brand: Mercedes-Benz Pages: 296
Westfalia 859528 Original Instructions Manual preview
859528
Brand: Westfalia Pages: 10
Goobay KFZ 112 Quick Start Manual preview
KFZ 112
Brand: Goobay Pages: 2
Ultraplast MD19 User Manual preview
MD19
Brand: Ultraplast Pages: 5

Brands by name

Popular brands

Load more brands